Hello there. I can't find the pressure-density chart of CO2. For example, I want to know the density of CO2 under 7 atm pressure at 20 °C.
You can't find the chart because there's no need in such a chart.
I'd say that at 7atm pressure the gas can still be considered as an ideal one.
Then we have N=P/k/T [1/m3] and
density = N*M_CO2 [kg/m3] where M_CO2 is a mass of a single CO2 molecule.
Substitute the values yourself and don't forget to use T in [K].
https://chembugs.files.wordpress.com/2015/12/perrys-chemical-engineering-handbook1.pdf
Refer to the link below:
https://www.engineeringtoolbox.com/carbon-dioxide-density-specific-weight-temperature-pressure-d_2018.html
Use this calculator.
Thank you for all the answers.
MAGNETISMIC GRAVITY What is magnetism? Something magnetic has a + and - charge. If 2 + or - are pushed if + and - are pulled. But what is the main reason for this? Why does magnetism have a pull...
21 February 2021 9,538 3 View
I am working on a biosensing project on paper substrate, however, it is found that the RNase contamination occurs on the filter paper. Might I ask is there any method to clean the paper surface...
12 February 2021 3,926 3 View
Hi everyone, I would really appreciate it if someone can tell me when and why a raw fluorescence starts below zero. In the picture attached below the blue colour curve starts from a negative...
09 February 2021 4,642 3 View
This is a follow-up on an earlier question regarding mechanistics of vaccines: why current vaccines don't block transmission. In summary, they don't engage mucosal immune cells to produce IgA....
08 February 2021 8,321 3 View
There are three hypotheses and I carry out direct effect and indirect effects with SEM. H1: There is a significant positive relationship between A and B. H2: There is a significant positive...
08 February 2021 9,141 3 View
In Abaqus I know that there are two methods for incrementation (Automatic and fixed incrementation). I want to control the incrementation by myself. I want to input the values of load increment...
03 February 2021 6,943 3 View
I want to quickly publish a data-report .Because there is a lot of data and it will take time to create the original article. But my main goal is to use that data-set in the original article. Is...
02 February 2021 9,779 7 View
Dear all. I'm modeling the RC column with cyclic displacement by Abaqus-Explicit. The concrete model used Concrete Plastic Damage model. However I'm facing with a error about the excessive...
01 February 2021 7,726 1 View
We are working on a study where we compare pre and post-workshop answers from a group of subjects. Subjects answered a question before the workshop and answered the same question after the...
17 January 2021 2,844 6 View
I am facing a problem that cellular debris observed in my SHSY5Y cells. I have seeded the cells in DMEM media with 10% FBS in T-25/ 60mm dish (antibiotic used PEN-Strepand gentamycin). I have also...
17 January 2021 3,074 3 View
When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...
03 March 2021 4,892 5 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...
02 March 2021 6,036 1 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...
02 March 2021 3,309 2 View
I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...
02 March 2021 5,829 1 View
Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...
01 March 2021 8,235 2 View
Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...
01 March 2021 1,907 3 View
I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...
01 March 2021 5,475 2 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View