Are there ways to chemically treat stainless steel to prevent the electroplating of metallic particles onto the steel? i.e. copper plating onto a stainless steel polymer filter
dear Thomas Cermack
in my suggestion the best way is to make a black anodized oxide layer on stainless steel using acidic bath. as in the following reference:
https://www.youtube.com/watch?v=xBHz4_YeQTw
If I have two polymer samples, both of the same formulation and relative viscosity, but one sample has a much higher amine end number than the other, can I assume that the sample with higher amine...
03 April 2018 796 3 View
I'm looking at potential differences in static generation for PA66 fibers as they are attenuated. I've attached a file containing drawings of fibers being guided into an attenuator. The fibers in...
10 November 2017 2,403 0 View
Consider nylon 6/6 pellets going from solid to melt in an extruder. My thoughts are that if you increase moisture content before they are melted, you can increase the monomer units that can...
07 August 2017 8,790 5 View
In regards to ambient air moisture absorption, will increasing hydrophobicity also limit the hygroscopicity of nylon 6,6? My thoughts are that by limiting the surface interactions of moisture,...
04 May 2017 4,178 5 View
Took out a steam sparger and noticed a small section that had residue on the top of it. I believe it may be caused by a reaction with HCL and moisture creating water and a metal chloride. It felt...
11 December 2015 2,736 3 View
Polymer in question is Nylon 6,6. Looking to understand flow through spin pack and how changes in the design will affect fiber spinning.
08 September 2015 4,070 2 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,290 1 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...
30 July 2024 6,420 1 View
I have multiple small samples of grass pollen with anthers. I want to find a method to identify concentrations of proteins, lipids, and other various elements for these samples. any suggestions?
28 July 2024 5,331 1 View
I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...
28 July 2024 8,027 3 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View