Cfd simulation of car parking

09 September 2015 0 6K Report

I am assisting my Dr and he asked me if i can get him with a CFD simulation problem or example concercing a ventillation system of a car parking. Can anyone please help? Its highly important to me.

Thank you

Badges
Science topic

More Rudolf Khalil's questions See All

What is a "working fluid inventory?"

How can it be measured? What is its equation?

11 December 2013 4,531 1 View

Can anyone share the UDF code concerning a 2-phase thermosyphon heat pipe, where II have an evaporator and condenser?

I have trouble concerning this subject.

11 December 2013 7,657 11 View

Can someone advise on the density of water vapor?

Water density at about 4 degree Celsius is 1000kg/m3 above 100 degrees Celsius it becomes around 958 kg/m3 so that means it is vapor. But i have been told that the water vapor density is 0.554kg/m3.

11 December 2013 4,691 12 View

What is working fluid inventory?

How can it be measured? What is its equation?

11 December 2013 7,804 1 View

Having trouble with fluent material separation?

I have a tube containing water on the bottom. I have to apply heat on its wall so the water boils and vapor travels through the rest of the tube. After drawing it on gambit and assigning its...

11 December 2013 7,323 3 View

Can anyone help with using a 2d modeling on ANSYS ICEM CFD v 14.0?

I am having difficulties trying to model this thermosyphon (attached pic) on ICEM CFD. I need to draw it, apply meshing, and then simulate it with different properties each time.

09 October 2013 3,399 4 View

How can i add an equation into a fluent to be plotted?

How can i add an equation into a fluent to be plotted? Can anyone write me a step by step method?

09 October 2013 5,184 4 View

Amir Faghri: Heat Pipe Science and Technology?

Does anyone have the above mentioned book on a PDF file or anything else? I am failing to find it anywhere.

08 September 2013 1,570 12 View

I'm looking for information concerning the performance of a closed two-phase thermosyphon, as well as generating it over fluent?

Vertical closed 2 phase thermosyphon studying its performance over fluent, setting parameters, schemes...

08 September 2013 1,912 6 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View