Cfd simulation of car parking

08 September 2015 5,477 0 View

What is a "working fluid inventory?"

How can it be measured? What is its equation?

11 December 2013 4,531 1 View

Can anyone share the UDF code concerning a 2-phase thermosyphon heat pipe, where II have an evaporator and condenser?

I have trouble concerning this subject.

11 December 2013 7,657 11 View

Can someone advise on the density of water vapor?

Water density at about 4 degree Celsius is 1000kg/m3 above 100 degrees Celsius it becomes around 958 kg/m3 so that means it is vapor. But i have been told that the water vapor density is 0.554kg/m3.

11 December 2013 4,691 12 View

Having trouble with fluent material separation?

I have a tube containing water on the bottom. I have to apply heat on its wall so the water boils and vapor travels through the rest of the tube. After drawing it on gambit and assigning its...

11 December 2013 7,323 3 View

Can anyone help with using a 2d modeling on ANSYS ICEM CFD v 14.0?

I am having difficulties trying to model this thermosyphon (attached pic) on ICEM CFD. I need to draw it, apply meshing, and then simulate it with different properties each time.

09 October 2013 3,399 4 View

How can i add an equation into a fluent to be plotted?

How can i add an equation into a fluent to be plotted? Can anyone write me a step by step method?

09 October 2013 5,184 4 View

Amir Faghri: Heat Pipe Science and Technology?

Does anyone have the above mentioned book on a PDF file or anything else? I am failing to find it anywhere.

08 September 2013 1,570 12 View

I'm looking for information concerning the performance of a closed two-phase thermosyphon, as well as generating it over fluent?

Vertical closed 2 phase thermosyphon studying its performance over fluent, setting parameters, schemes...

08 September 2013 1,912 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View