Can you tell me how to coat nickel by polyacrylonitrile?

12 November 2013 0 4K Report

I want to coat all the foam porous structure of nickle foam by very thin layer of polyacrylonitrile without loosing the porosity of the foam.

Badges
Science topic

Similar topics
Engineering
Modeling

More Rassoul Tabassian's questions See All

Is there any photoresist that could be dissolved in water after being developed?

I'm going to use photolithography to make a mold for PDMS casting. However, because of the high aspect ratio of the features, peeling the PDMS off is not easy. So I'm looking for a water-soluble...

03 March 2024 4,668 2 View

How to selectively coat two combined microlattices with two different polymer?

Suppose we have two combined structures that are conductive but not electrically connected to each other (please check the figure). Is there any way we can selectively coat only one structure with...

22 February 2023 8,953 5 View

What is the best solvent for making carbon black suspension and then freeze drying?

I'm going to make a suspension of Carbon black in order to mix it with another water base suspension and freeze-dry it. considering the point that carbon black does not mix with water properly I...

27 February 2018 3,163 5 View

Can Cyanamide produce toxic material in high temperature?

I'm going to prepare some N-doped Carbon by using Cyanamide. To do so, I need to increase the temperature up to 950 C. I'm wondering if this process can produce any toxic product.

09 February 2017 4,972 1 View

What is the criticism concept in the public sphere according to the habermas thought?

I want to study carefully about position of the criticism in the public sphere theory, according Habermas thought . On the other hand I want to know how the criticism can solve political conflict ...

11 January 2015 8,458 9 View

What is the best solvent for nickelocene?

I'm going to solve nickelocene (bis(cyclopentadienyl)nickel) in an organic solvent and achieve a clear solution. I tried dichlorobenzene but it didn't solve completely. It was more like a...

24 February 2014 8,420 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

Technology developments may it for whatever reasons developed eventually its benefits are multi-Disciplinatary?

Your comments

28 July 2024 2,822 2 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View