I am trying to simulate phase change of refrigerant inside pipe extracting heat from panel in comsol. Can anyone help with how to simulate this?

My model is a rectangular multi layered structure under which refrigerant flows through cylindrical pipes. A heat flux of 600W/m2 applied on panel and internal forced convection is used for...

20 January 2021 9,478 1 View

Why does the ghost atoms gives error in NICS calculation with wb97xd in gaussian09 ?

In a trial, I am trying to calculate NICS (0 and 1) values for benzene ring using gaussian09. I have placed the ghost atoms at the center, 1A, and 2A above the rings. On using the method/basis...

19 January 2021 3,188 3 View

Rejected manuscript for journal publish after 1st revision, what needs to be done next?

Hello, My manuscript has been rejected by the editor and reviewers even after the 1st revision. Though I tend to disagree some of the points raised, assume I can't request for another revision...

28 December 2020 6,062 3 View

Acetylene reduction assay procedure?

Do anyone have the detailed step wise procedure(practical) to do the acetylene reduction assay? Or if anyone can let me know in which institute can i analyse my samples in India?

28 December 2020 6,717 2 View

How to capture UV- fluorescence from a substance using a camera?

I have a liquid that glows when UV light is shined. However, when I use my phone camera I can't see the glow, I just see a violet hue. What is the best way of capturing the fluorescence-glow from...

02 October 2020 8,664 3 View

What is the actual basis on which amount of Perovskites materials are to be taken?

In some discussion people took 112 mg of MAI and 461 mg of PbI2 in 1 mL DMF and some took 461mg of PbI2 too but 159mg of MAI there are many other authors took different amount of these materials...

17 September 2020 9,998 3 View

Forums to get online survey responses?

For my journal publish, I have been asked to increase the sample size by 200. I have been individually contacting more than 1000 Linkedin contacts and posted in all professional groups. But have...

04 September 2020 2,564 5 View

Derivation of Rice and Tracey equation???

12 July 2020 6,555 1 View

Can anyone suggest me where to get a low cost 2D Heterostructure Transfer System?

Except the 2D transfer system sold by HQ Graphene

09 July 2020 3,276 4 View

What digital technologies are more helpful to sustain Agriculture?

With the global Corona Pandemic situation, it looks to be inevitable to move towards digital technologies to get adapted in various farming sectors. With the advent of IoT, Robotics, Data Science,...

10 May 2020 8,570 5 View

Trouble with Charting with Google Earth Engine (Technical)?

Hello. I have a problem with the charting in google earth engine. I created an image collection by combining 5 image collections of five parameters and using ee.Join.inner ( ) and .apply ( )...

26 February 2021 7,084 2 View

How long does it take to get a modeller(for homology modelling) license?

I submitted my e-mail address on modeller website to get a license. The problem is that, the site cannot process my school e-mail (ewhain.net). I submitted my Lab website and school name so that...

25 February 2021 9,054 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View

PV system design. 3d modelling and Analysis?

I have been looking for a good cost-effective tool for 3D modelling a glass-glass solar module system. I was initially considering Skelion as a tool but it does not look very promising, a bit...

13 February 2021 8,126 1 View

Why the battery connected on the load side for storing purpose is taking the volatge /current at whatever rating it is given in matlab simulation?

I am designing a DAB DC DC Converter and when I am connecting a battery block in Matlab and fix its specification lets say 350 V and 25 A, when I am giving input as 600V, Battery would charge to...

11 February 2021 3,110 1 View

2D wavelet transform?

Dear all I have a 2-dimensional mode shape of one concrete beam and I put the data of mode shape in a matrix (69*3) which the first column in the matrix is x coordination of my beam and the second...

10 February 2021 3,301 3 View

Is it possible to get compass potential paramters from MATERIALS STUDIO 6.0?

Hi all, I wonder whether we can get potential parameters from material studio. I have a licensed version available. If I use polymers and cnt in materials studio to perform MD simulations,...

03 February 2021 7,673 3 View

I want to extract engine oil from a soil sample,please how much amount of anhydrous sodium sulphate am i going to add to 10kg soil?

Engine oil extraction from contaminated soil,10kg of contaminated soil+20ml of dicholoromethane+? of anhydrous sulphate

01 February 2021 9,509 1 View