Can you help me with sequential monte carlo simulation?

More Yorlandys Salgado Duarte's questions See All

In which dry organic solvent/solvent mixture molten 1H-imidazole could be precipitated at 100%?

I am trying to isolate an allkylated imidazole from a mixture containing unreacted 1H-imidazole. The problem is that imidazole is slightly soluble in my targed molecule. Furthermore, I need to...

04 November 2020 4,513 3 View

Bioinformatic tools to determine ploidy in microbial genomes?

Looking for tools with proved accuracy to detect ploidy levels in microbial whole-genomes.

14 October 2020 4,273 3 View

No title

I'm currently working in a project in which it would be useful to measure: transmural flux, resistence and potencial difference in mucosa biopsies. I've been reading about this method and as far...

23 September 2020 6,976 1 View

Is there any suitable approach to solve the LCPN method in hierarchical classification?

I have a multi-class problem. I want to solve this problem using the LCPN (Local Classifier per Parent Node) method of heirachical classification. Therefore, I have manually divided the original...

22 February 2020 2,829 3 View

How to implement hierarchical classification using python?

I have a multi-class problem. I want to solve this problem using the LCPN (Local Classifier per Parent Node) method of heirachical classification. Therefore, I have manually divided the original...

18 February 2020 1,147 2 View

What can be causing uneven focus on IHC-P stained slides?

Hello, I have been performing some IHC staining on parafin embeded tissue. All was good until recently. In the latest slides I have prepared, when looking under the microscope, some areas need to...

12 February 2020 9,906 3 View

How can I define a custom cohesive response to use with contact pairs in ABAQUS?

Hello, I have a problem in which a steel nail is 'embedded' in a wood piece. The head of the nail is in contact with a steel bracket. As I apply cyclic load on the vertical wood 'wall', the...

09 July 2019 8,084 2 View

[COMSOL 5.1] Simple FSI simulation not converging. Can someone please take a look at my model?

Hello, I'm a newbie on CFD and starting to learn how to use COMSOL. I tried to modify one example from COMSOL but it isn't working. I think it has something to do with Inlet velocity, but i...

11 April 2019 2,662 3 View

How can I use FSI+Piezoelectric module in COMSOL Multiphysics?

I am trying to model Piezoelectric effect using vortex induced vibrations on a cylinder attached to a fixed beam while the end of the beam has a piezoelectric patch in 2D, but when I add the...

27 March 2019 6,694 3 View

Is possible to remove a co-author who only participated in the reasoning of a paper but who did not write or analyze anaything?

this is an ethical question. We have a conflict with a co-author who stopped its contributions, he only participated at the beginning of the project. I did all data analysis, article writing and...

04 March 2019 3,207 6 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

Keran O'Brien

Can you test the modules of the code one by one? Do you trust the literature?

Yorlandys Salgado Duarte

For example'm modeling Billiton 6-node system for maximum demand and LOLE in the literature is around 73 hours a year. With the simulation of non-sequential monte carlo agree with the outcome, but with sequential monte carlo simulation result I get is 55 hours per year. The simulation is performed in the matlab and can not find the problem.

Eugenio Torres-García

Did you write the code? What kind of particles are transport the code?