Can we use vacuum degassing method for expulsion of carbon dioxide in Boehm titration?

04 April 2017 1 658 Report

In Boehm titration, degasifying the acidified samples is an important step and there are various carbon dioxide expulsion methods. So will it be possible to remove carbon dioxide completely through vacuum degasifcation ?

Ali hussien Amteghy

this maybe help you

Badges
Science method

More Shilpi Das's questions See All

By which mechanism zinc chloride works as an activator in the preparation of activated carbon?

Activated carbon is prepared from lignocellulosic biomass using ZnCl2 as the activating agent. What is the possible reaction between zinc chloride and the biomass?

02 March 2018 9,517 4 View

How can I maintain pH of heavy metal solution using buffer?

For maintaing pH of heavy metal NaOH and HCl is added in a dropwise manner to the solution. But how can a buffer be used for maintaining the pH of the solution? Kindly give vivid explanation.

01 February 2018 8,307 4 View

Why is it not possible to maintain the concentration of Mohr's salt solution after adjusting the pH?

Suppose I have prepared initial concentration of 10ppm(100 ml). After maintaining pH (2-6) by 1M NaOH and 1M HCl , it's original concentration decreases to a great extent, so what can be the...

31 December 2017 9,742 3 View

Why is it necessary to maintain pH before carrying out adsorption process?

Suppose we are preparing 30 ppm sample and then maintain its pH by 1M NaCl or 1M HCl. I have seen that the concentration of the sample reduces a lot after maintaining pH. So, what is the purpose...

11 December 2017 1,645 3 View

Why is langmuir surface area always higher than BET surface area?

Langmuir corresponds to monolayer adsorption whereas BET denotes multilayer adsorption. So, what is the reason behind Langmuir surface area to be greater?

06 July 2017 2,548 8 View

What is the reason for the presence of a hysteresis loop in the Type I N2 adsorption-desorption isotherm?

The curve yielded the features of Type 1 isotherm but the adsorption capacity continues to increase with an increase in relative pressure. So is my assumption correct regarding the type of...

05 June 2017 2,121 8 View

Is it possible to get (-ve) lactonic and carboxylic acid groups from Boehm titration of ZnCl2 activated carbon?

The Boehm titration of ZnCl2 activated carbon indicated basic sites of 0.525 mmol/g and 0.85 mmol/g phenolic groups with -0.19 mmol/g and -0.26 mmol/g lactonic and carboxylic groups. The total...

05 June 2017 4,938 1 View

What should be the zero point charge value of base impregnated activated carbon?

The activated carbon was prepared by impregnating zinc chloride with the raw sample. I have carried out zero point charge by salt addition method and obtained a value of 7.03. Is it correct?

04 May 2017 8,370 6 View

Can zero point charge of activated carbon be determined by salt addition method ?

I want to determine the zero point charge of activated carbon. So which is the best suitable method for it and is it neccessary to degasify the solution while measuring the final pH in order to...

03 April 2017 8,758 3 View

How can I know whether a journal of Elsevier publication is Sci indexed or not ?

I am facing problems while confirming whether the journal is Sci indexed or not. Some journals of elsevier publications are having no impact factor but they are having SCImago Journal Rank. So...

11 December 2016 9,958 4 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

How to isolate lymphocytes from mouse spleen?

I have tried several times to isolate lymphocytes from mouse spleen, but all attempts have been unsuccessful. I tried most available protocols. I used different dissociation media (HBSS with Ca...

04 August 2024 9,913 7 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

How to make Boehm titration ?

Hello Everyone, While doing Boehm titration, We use nahco3 in order to determine carboxylic acids. Then the mixture was agitated. After a while, the solution was filtred and HCl was added. After a...

29 July 2024 4,048 4 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

Do some Staphylococcus aureus strains have in vitro antimycobacterial activity ?

Some Staphylococcus aureus strains Inhibit the growth of Mycobacteria in Mueller Hinton Agar medium containing 10% OADC. Do some Staphylococcus aureus strains have in vitro antimycobacterial activity?

29 July 2024 10,023 2 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View