Can we do background subtraction after refinement in FULLPROF?

More Sai Pranav Vanam's questions See All

How to install Rietan-FP(for analysing PXRD) in windows operating system.?

I have downloaded Rietan-FP from http://fujioizumi.verse.jp/download/download_Eng.html I am finding trouble to install in PC.

10 November 2018 2,037 4 View

Why single crystal XRD data is 3D where as Powder XRD data is 1D.?

I am not able to understand why the data we get from single crystal XRD is 3D where as from powder XRD is 1D.? How did we define it as 1D and 3D.?

02 March 2018 6,726 2 View

How to find the delta G of the material having polymorphic change either same crystal system (i.e., different space group) or different ?

I am having a material which changes from one space group to another with change in temperature. I would like to how to calculate the free energy (delta G) change as a function of temperature and...

01 February 2018 5,944 4 View

Can we predict the occupancy by using Rietvleld method from the powder diffaction XRD data.?

I have done the Rietveld analysis of a oxide sample by using fullprof. The initial given occupancy values are much different than the obtained values after Rietveld. So, my doubt is, whether can...

03 April 2017 5,930 7 View

Can we find the Position of atoms by using XRD data.?

Like say TiO2. we can find a,b,c, angles, structure,space group from XRD. but can we find the position of Ti,O in the unit cell..?

01 January 1970 7,004 11 View

My 2nd Discharge in Lithium air(Li-O2) battery is not efficient as that of 1st..? Why..?

I am using Co3O4 as Catalyst for Li-air battery. 1st discharge is aroung 1.4mAh but 2nd discharge is cut to more than half. I dont understand the reason. Please can anyone give me where I am going...

01 January 1970 5,641 5 View

How to find whether the compound is P-type or n-type semi-conductor.? Ex: Co3O4. How to determine it theoritically

Thoritically how can we say that Co3O4 is a p-type. what are the methods for doing it. electronic sharing, electronic configuration, physics route or chemistry route

01 January 1970 6,359 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Why the CHi^2 is close to zero with a bad fitting but the Rp and Rwp are still high?

I am refining my XRD data using in FullProf program. The intensity of the modulated X-ray peaks is almost flat. I tried to adjust the peak intensities but unsuccessful. What is the reason? I guess...

23 February 2021 2,304 4 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

Why CHi^2 is reducing if I divide the intensity by a constant factor?

I was refining my XRD data in FullProf. Highest intensity was 400000. The fitting was good but still the Chi^2 value is very high (0.174E+04) I divided the intensity by some constant factor (say...

17 February 2021 3,383 5 View

Dinesh Kumar

In all the refinement software there always present option for the correction or fitting of the background of the XRD pattern using different method. So like other structure refinement software FullProf also has option for background correction. You can correct background during refinement or after refinement of the structure.

Sai Pranav Vanam

I have done the refinement, during refinement we do the background correction. My PXRD data has a hump at lower 2theta, to correct it i need background subtraction which is generally done in GSAS at the end( after the refinement). I need to know is this option available in FULLPROF