Is it possible to remove the titanium-based coating using any solvents/ acids or other chemicals from the steel without affecting the surface of the steel?
Thank you @Francois, for your detailed suggestion. I am surely going to try this very soon. I shall get back to you.
I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...
05 August 2024 9,803 3 View
My research sample size is 383. I want to analysis following structural equation model. So I want to advice which software is better smart PLS or Amos.
04 July 2024 4,987 3 View
While I was amplifying a certain gene from chromosomal DNA for my Gibson Cloning, I noticed after sequencing that there is one extra A on the middle of my gene of interest sequence. In the...
02 March 2024 1,066 7 View
Hello, I have come across a paper where it is stated that Sequence identity between these two proteins is ~36%. I performed BLAST and in the summary section, it is stated that that percent...
16 January 2024 1,478 2 View
Hello, I am working on a protein that belongs to NUDIX family hydrolases and therefore requires Mg ion as a cofactor. But the protein that I have downloaded from PDB is an apoprotein. I want to...
11 January 2024 8,105 2 View
Dear all, I have developed a pharmacophore hypothesis using receptor cavity since my protein has no co-crystallized ligand. I , now, aim to validate it using a set of actives and decoys. I tried...
30 November 2023 1,424 0 View
Also, is there a way to convert SMILES into IUPAC or common name of the compound?
30 November 2023 304 2 View
I have a protein that binds to ATP and another nucleotide. I want to dock them so that I can find out the binding site residues in the protein. Which tool can I use?
10 October 2023 8,217 4 View
How to correct of desk reject of an article
08 October 2023 4,163 1 View
I have a 3D-structure of a protein, but it is an apoprotein. I am using Maestro for molecular docking. I want to find out the protein binding site in my protein.
27 September 2023 1,748 7 View
"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....
10 August 2024 8,617 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 940 3 View
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,991 0 View
Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...
08 August 2024 6,133 12 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,297 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,524 4 View
I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.
06 August 2024 6,795 3 View
There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...
06 August 2024 7,101 0 View
How can I measure the thickness of thin film by Uv-Vis?
06 August 2024 7,808 3 View
In the case of a wound l recurrence after radical breast cancer and sentinel lymph node biopsy. Are the sentinel lymph node procedure recommended? If no axillary lymph node dissection was not...
05 August 2024 8,054 1 View