Can the model settings for Cognitive Radio simulation in NetSim be increased?

09 September 2014 1 2K Report

Hello,

I had a few queries on model / parameter settings for CR simulation in NetSim

a. The maximum number of CR stations supported under one BS is 255. Can this be increased ? If not why is this the limit

b. How do I increase the distance beyond 500 m ?

Thanks

Kumar Saurav

Hi Kishore,

Thanks for your response.

In NetSim there is TCP / UDP in layer 4 and in TCP there are various option. I read that the most widely used are Reno or New Reno and wanted to run the scenario using one of these algorithms. Can some one please help on difference between Reno and New Reno ?

Badges
Science topic

Similar topics
Philosophy Of Science
Models

More Kumar Saurav's questions See All

In NetSim where and what code needs to be added to print the distance between the various sensors and the agents that are being sensed by the sensors?

See above

10 November 2014 624 3 View

How do you get device position in NetSim?

Hello, I am trying to print the sensor positions in NetSim using DEVICE_POSITION(DeviceId)->X, DEVICE_POSITION(DeviceId)->Y However, when printing this into the file the X, and Y...

09 October 2014 1,250 0 View

How can I get the end-to-end delay for WSN simulation in NetSim ?

I am simulating a WSN based network in NetSim. The GUI, Config file, simulation parameters etc have been configured and I am getting various output metrics. However, I want to calculate the...

05 June 2014 1,273 5 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

What analysis to choose with a large neste dataset and clearly skewed or kurtotic distributions?

Hello! I have a dataset of n=3000 nested within 8 countries with approximately 200 or 400 responses in each country. I originally planned to perform multilevel modelling with 4 dependent variables...

02 March 2021 6,865 1 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View