How do you get device position in NetSim?

10 October 2014 0 1K Report

Hello,

I am trying to print the sensor positions in NetSim using

DEVICE_POSITION(DeviceId)->X,

DEVICE_POSITION(DeviceId)->Y

However, when printing this into the file the X, and Y co-ordinates are shown as some very large number (1076101120,1076101120).

Does anyone know why ? Please assist. Thanks

Badges
Science topic

Similar topics
Methodology
Sensors

More Kumar Saurav's questions See All

In NetSim where and what code needs to be added to print the distance between the various sensors and the agents that are being sensed by the sensors?

See above

10 November 2014 624 3 View

Can the model settings for Cognitive Radio simulation in NetSim be increased?

Hello, I had a few queries on model / parameter settings for CR simulation in NetSim a. The maximum number of CR stations supported under one BS is 255. Can this be increased ? If not why is this...

08 September 2014 2,308 1 View

How can I get the end-to-end delay for WSN simulation in NetSim ?

I am simulating a WSN based network in NetSim. The GUI, Config file, simulation parameters etc have been configured and I am getting various output metrics. However, I want to calculate the...

05 June 2014 1,273 5 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

What are the patterns of human behavior that lead to COVID-19 infections?

Does data from contact tracing help in establishing patterns of behavior and social interactions that lead to infections? There are cases here in the Philippines where patients have no travel...

25 February 2021 9,002 13 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View