Can the first singlet excited state (S1) have lower energy than the triplet state (T1)?

01 January 1970 0 10K Report

Usually S1 state has higher energy than T1. But can it be possible for a molecule to have S1 state lower in energy than T1?

Badges
Science topic

More Kalyan J Kalita's questions See All

How to check leakage current of Si-SiO2 wafer?

I want to use the n-type Si wafer coated with a 300 nm SiO2 layer for the OFET device, but for that, I have to check the leakage current of the dielectric layer. how?

07 February 2024 4,115 2 View

What will be the quality of Al2O3 layer in OFET device fabricated through RF Sputtering?

This question is related to OFET devices. Please suggest some answers to this question.

07 February 2024 8,067 0 View

How to extract velocity data of a moving object from a simulation done in Ansys Fluent?

Hello Everyone!! I am currently working on a model for renewable energy harvesting using ocean wave energy in Ansys fluent. I have applied a dynamic mesh and compiled the UDF for motion of a...

30 January 2024 8,896 1 View

How to remove negative volume error in Ansys fluent dynamic mesh?

Hello Everyone!! I am currently working on a model for renewable energy harvesting using ocean wave energy in Ansys fluent. I have a design ready along with a UDF for a moving component. But when...

08 October 2023 5,531 5 View

How to solve highly non linear coupled eqn. ?

send me a matlab program

22 August 2023 7,317 2 View

What is the concentration of antibiotic for PCR 2.1 TOPO cloning?

Ampicillin 50ug/ml is what specified in the kit, means should I use 5 grams of ampicillin for one liter of LB agar?

15 August 2023 7,603 2 View

How can we isolate exopolysaccharide content from cyanobacterial strains?

Is there any method for isolating exopolysaccharides (not the total Carbohydrate) from cyanobacteria?

06 August 2023 4,234 2 View

Where do i get elastic compliance constants required for the orthorhombic crystal structure?

USDM and UDEDM model of Williamson Hall plot, elastic constants are required to calculate the Youngs modulus which further usefull in calculating stress and deformation energy density. I am...

12 June 2023 1,425 0 View

How can I find or estimate the species specific parameters α and β for application in Beta-poisson model for QMRA?

I am trying to estimate the QMRA for three species of bacteria using beta-poisson model. The literatures that I followed have not reported the α and β values for these 3 specific bacteria, while α...

27 May 2023 5,692 0 View

Q-Exactive calibration error for Mass resolution Dependency too high, can anyone help?

Hi, After performing my annual cleaning on the QE and calibrated, it as passes the positive cal but when performing the basic (negative) Analyzer accuracy it has failed for Mass resolution...

08 January 2023 2,206 1 View

How to solve Gaussian Convergence failure?

To whom it may concern, I'm working on optimizing the molecule using gaussian 16. However, it is suffering from the problem of convergence failure. I attempted optimization several times, but...

30 May 2024 6,373 3 View

How to get rid of "error termination in SCF gradient" in ORCA 5.0?

I am optimizing a small organic molecule in a triplet second excited state using TD-DFT in ORCA 5.0. It is giving error termination in SCF gradient. How to get rid of it? Check the error below....

30 April 2024 6,806 6 View

Discrepancy in T1 States using Gaussian?

Hello, I am a grad student working on a project on the photisomerization of 2'-hydroxychalcone. I was instructed to create a PES surface for the triplet state. My first attempt did not produce...

21 March 2024 3,585 1 View

First singlet excited state optimizacion weird result?

Hello all, I hope someone here can help me with some TD-DFT calculations. I am trying to calculate the excited state optimised structures and energies of some Germanium compounds. Firstly, I run...

20 December 2023 4,593 2 View

What determines the optical decay constant in hybrid semiconductors?

Considering the molecular complex, we can discuss photoluminescence dynamics with energy level argument. There, triplet states have longer decay constant comparing with singlet one. We can design...

17 December 2023 4,123 1 View

How to Calculate Energy Difference for TADF Compounds?

The triplet energy stands as a crucial factor in adjusting the emission of TADF compounds. Discovering how to measure and calculate it using simple techniques is essential.

03 December 2023 6,677 1 View

In UDFT optimization, what is the energy order between different spin states of Fe and Co's?

For Fe (Singlet, Triplet, Quintet) and Co (Doublet, Quartet), what is the correct energy order between Fe and Co's spin states in Gaussian after geometry optimization by UDFT?

04 September 2023 8,285 0 View

How do I calculate the singlet-triplet energy gap of CF2 using Gamess?

How to optimise the singlet and triplet forms

28 August 2023 2,663 0 View

Can I make wound healing assay in a 48-well plate?

Dear all, I think that usually wound healing assay are made in 12- or 24-well plates. However, I need to test different drugs in triplets as single treatments and some of them in...

23 August 2023 1,311 4 View

How to calculate the experimental triplet energy of the organic molecules?

I found the same information in the literature. But the confusion is, in some literature, they take the onset value at the peak beginning, and in some are taking onset value of the peak ending or...

12 July 2023 7,124 2 View