Can someone tell me of permeable coating of the carbon fibers electrodes?

11 November 2016 0 10K Report

i am looking for literature for permeable coating of the carbon fibers electrodes so that i can install it into textile. can someone refer or send me any literature in this regard.

Badges
Science topic

More Amjid Rafique's questions See All

About anodic and cathodic peaks in Cyclic Voltammetry?

Is there anyone to explain me about the CV behavior of carbon based composite of Vanadium Nitride in which i am clearly obtaining anodic peak around -0.5 V vs Ag/ AgCl but there is no cathodic...

06 July 2018 6,328 1 View

Coulombic efficiency >1?

what if coulombic efficiency of supercapacitor at higher scan rate greater than 1.? Is it possible to have coulombic efficiency greater than 1? Is there anyone to explain what is happening. I am...

05 June 2018 8,499 0 View

How can I solve this problem of capacitive charge storage curve?

Hi everyone, i am calculating capacitive and diffusive control charge storage behavior of MnOx and i have problem that when i calculate just capacitive behavior its curve crosses at certain...

09 October 2017 4,435 2 View

Can someone suggest me a software to make graph for paper ?

i am taking original graph from origin software and put them in paint to make PNG. but their text look dull. will someone suggest me any software to make graph?

01 February 2017 9,663 0 View

Is calculating capacitance for two electrodes asymmetric configuration same as for symmetric configuratio n?

i want to calculate specific capacitance for asymmetric configuration. Is this same as for symmetric configuration?. i am using two electrodes configuration.

31 December 2016 8,291 5 View

Can i use NaOH for electrochemical activation of the carbon fibers?

i need to activate carbon fibers. can i used NaOH for electrochemical activation of the carbon fibers

10 November 2016 4,676 2 View

How to calculate energy density and power density in wh/cm and w/cm?

i want to calculate energy density and power density in wh/cm and w/cm . can some one guide me in this regard how i can calculate in these units

06 July 2016 5,844 3 View

Can i calculate capacitance for Asymmetric configuration using same equation as for symmetric ?

i want to calculate the specific capacitance of the asymmetric electrodes. i used two different electrodes . can I used the same method to calculate the specific capacitance as i used for...

01 January 1970 4,874 0 View

Can i calculate capacitance for Asymmetric configuration using same equation as for symmetric ?

i want to calculate capacitance of supercapacitors for asymmetric configuration. Can someone tell me if it is same equation can be used for this configuration when we are using two electrode...

01 January 1970 9,752 0 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Who of all of you will help TPEOM to re-originate the Earths atmosphere to it original 5 atmospheric elements/gases?

Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...

06 August 2024 8,716 0 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View