Can one do SEM-PLS (Structure Equation Model (Partial Least Square) on 5-Likert scale?
Yeah, Of-course you can do that.
In market research Industry people are doing all this flawlessly.
Yes you can
Hello every one, I am doing a research paper, And I want to make sure that if X is a sum of a*CosΘ and Y is the Sum of a*SinΘ my question, is the expected of E(sum(acosΘi))*E(sum(asinΘi))=0...
10 November 2018 7,029 1 View
Hello, Am trying to set up ARIMA model for the attached graph, can you please advice me with best setting I can use is it ARIMA (1,0,0) or any other option? Thanks
02 March 2018 5,343 1 View
Am trying to find the relation between two nominal variables, I did chi-square test for measuring the independence between two variables, but, one of my variables has a massive frequency in one of...
07 August 2017 9,895 4 View
I found someone say: "There are few consequences associated with a violation of the normality assumption, as it does not contribute to bias or inefficiency in regression models. It is only...
04 May 2017 3,452 16 View
If I decide to go for a census normality test won't be needed, but if I stick to a sample then does my data need to be normal for regression and SEM?
03 April 2017 9,018 5 View
I have a population of 552, the sample size is 227. the sample size is large compared to the population, with the non-response expected, is it better to conduct a census? What is the best...
03 April 2017 3,597 6 View
Am trying to examine the effect from my independent variables using mediation effect in the middle (OCBs) toward the dependent variable (employee performance), as I knew before, I can use SEM...
01 February 2017 679 7 View
"Errors are found in this table. In the lower part of the table, all the p-values are exactly in the same (i.e., 0.000). These are impossible as at least the 13 insignificant p-values must be...
10 November 2016 7,588 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View