Can i use SBDART radiative transfer model for atmospheric correction of MRO CRISM data ?

More Farzana Shaheen's questions See All

What is the average stove efficiency for household gas stove especially in the Indian subcontinent?

In one paper, I saw it to be about 36%. But as the paper was published in 1997, shouldn't modern household gas stoves be more efficient?

14 December 2020 6,199 6 View

Is there a guide for Aspen Hysys to show unit operation calculations?

For example, let's say if I design a conversion reactor and give inlet temperature,pressure,composition and reaction kinetics then Hysys will show me the outlet conditions. It doesn't,however,show...

09 December 2020 8,375 3 View

Which decision rule algorithm is best in machine learning? Is there any algorithm based on rough sets that gives good results?

I am trying to learn some algorithms that extract decision rules from data sets, particularly by using rough sets. I need to know whether they are reliable and efficient (like LEM2) for real datasets?

17 August 2020 7,013 6 View

I have generated themes on the basis of research questions. Is my analysis thematic or content?

During interview and observations I asked questions keeping in mind themes. After that I analysed and data on the basis of themes. Is it content or thematic analysis?

12 February 2020 3,697 8 View

Does surface particle size (surface component) has any relation with atmospheric optical depth (atmospheric component)?

I have estimated thermal inertia for a surface followed by its particle size, I have to look for the relation between particle size and atmospheric optical depth, I have gone through the...

11 October 2019 7,986 3 View

Techniques which can be used for delineating the rim of a feature?

Hi, I want to delineate the rim of this crater (refer attached image) using remote sensing software, apart from visual interpretation what are the other available techniques which i can opt...

06 September 2019 9,987 3 View

Is there any data set from where i can find country wise data on FDI & portfolio investment inflows in Pakistan?

i need data on private capital inflows in Pakistan, for this sake i have to generate the variable by adding FDI in the reporting economy and the private elements of portfolio investment, financial...

07 July 2019 4,316 5 View

Extracting maximum elevation points between 0.8R and 1.2R?

I have xy location and radius, from these details i make buffer of 0.8R and 1.2R, then i have divided the circles into 36 segments with an interval of 10 degree. I have DEM image of this region....

08 May 2019 4,892 2 View

How can we justify that it is the interference pattern of electromagnetic waves?

I designed double slit experiment using RF module in COMSOL and tried to get interference patter, The results are following with 930MHz frequency. What do you predict from the pattern?

21 January 2019 8,356 2 View

Including Renewable Energy Sources in Matpower to solve Optimal Power Flow?

I'm modelling my own grid in matpower to calculate the optimal power flow (opf). The thing is my grid has WT, PV & batteries in them along with the conventional generators. Does anyone know...

29 December 2018 4,379 6 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Vipin Suresh

yes it can

Xiaoguang Xu

Please be aware that SBDART uses LOWTRAN. This means the spectral resolution for gas absorption is rather coarse. You may check out the UNL-VRTM (www.unl-vrtm.com), which implements HITRAN gas absorption and is free to the public. However, to use either SBDART or the UNL-VRTM, you will probably need to provide a Mar's atmosphere for simulating the MRO CRISM data.

Farzana Shaheen

Thanks for the reply Mr. Xu. To be honest, I am not a programmer and this is my first time trying it out. I will try to follow your suggestions above and reply back in the comment.

Ran Yinze

Hi, i don't know how to set the output inthe sbdart so that the model can simulatethe radiance of 3.9um and 11um，i hope you can give some suggestions, thanks for a lot