Can I sample either in the middle or from the side of the vessel?

More Vipul Patel's questions See All

Control in microstructure with growth inhibitor?

Dear researchers, I wish to understand the role of grain growth inhibitor in controlling the microstructure of the ceramic pellet. How it controls the growth? Also, I wish to know the grain...

15 January 2021 3,859 3 View

No title

11 January 2021 3,284 3 View

How can we count the number of edges in an edge detected image using canny/sobel algorithm in MATLAB?

I need to process an image for edge detection and then want to count the number of edges in that image.

29 December 2020 5,594 2 View

Asalam o alikum, Can anyone please help me in interpretation of XRD data?

Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.

28 December 2020 6,769 4 View

Is it need to test Cronbach's Alpha for extracted features from data?

As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...

26 December 2020 9,602 2 View

What are the invivo screening methods for anti TB drug?

what are the invivo screening methods for anti TB drug?

25 December 2020 722 1 View

Which are the vendors who sell commercial SWIR (NIR-II) dyes?

I am searching to find commercial vendors who sell SWIR dyes. I could only find Nirmidas Biotech which sells different NIR-II dyes!

23 December 2020 5,002 3 View

How to get doi of presentation ?

doi of your presentation in the conference

23 December 2020 9,370 2 View

Doping of r-GO?

if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...

21 December 2020 6,091 3 View

XRD peaks for gold nanoparticles ?

is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...

17 December 2020 9,275 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View