Can I compare a film-form blank and powder-form MNC, or will results be affected?

13 May 2025 0 5K Report

I have synthesized a metallic nanocomposite (MNC) and a blank compound without metal for comparison. However, the blank material is in film form, while the MNC is in powder form. Can I proceed with the comparison between them, or will the difference in physical form affect the reliability of the results?"

Badges
Science topic

More Sakshi Saini's questions See All

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

How to retain amplicon yield after Ampure bead cleanup, following a 2-stage PCR protocol?

Hello all, I have been trying to follow a 2-stage PCR protocol used to amplify barcodes of a large yeast library, as per Nyugen et al. (2022) -...

30 July 2024 841 2 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

How Can I Resolve a Persistent Unwanted NMR Peak at 1.25 ppm?

Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...

15 July 2024 9,065 4 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 781 0 View

How to conduct the NMR study of a nano-composite film?

Solid state NMR study

03 July 2024 422 1 View

Does anybody know if amino acids like GABA, BABA, proline, lysine, valine or any other non-aromatic amino acid are destroyed by UV light?

I am trying to eliminate infection from my plates and therefore, gave UV treatment after addition of amino acid (used for better growth). Can you please suggest if UV destroys amino acids or not,...

02 July 2024 2,922 1 View

What are the recommended rapid response scopus indexed journals in computer science?

Kindly provide their URLs. Thank you

30 June 2024 8,475 0 View

Is anyone who knows how to buy AMOS sofware?

I have been working in Hanoi University of Public Health. I would like to know where and how I can buy AMOS software?

28 June 2024 6,593 1 View

How to form the state space model of SMIB with Power Electronic Load?

I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...

26 June 2024 2,496 1 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

Please introduce me the latest published articles on the structure and properties of metal nanocomposites?

26 July 2024 2,200 3 View

How can I better use imageJ to get good result on calculating surface area of a film accurately?

I have images of film formed on the bottom of a 50mL beaker, and I have been trying to figure out the surface area. I could easily use features on imageJ to do that, but I want to know which area...

23 July 2024 4,461 1 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Why can't I detect the plasmon resonance angle with water?

I am trying to measure the plasmon resonance angle of gold film and pure water using the Kretschmann configuration and a 633nm laser. Without flowing water over the gold, I can detect a clear...

10 July 2024 4,719 3 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

I want to ask why the poly aniline film does not stick to the ITO type substrate knowing that I used the electrodeposition method?

In order to make a polyaniline film, I used the electrodeposition method and set all the conditions, but I noticed that the polymerization process is happening, but it doesn't stick to the...

09 July 2024 2,708 2 View