Can anyone tell me the reason why the GSAS refinement shown like the below attachment?

02 February 2015 1 6K Report

peak position

Very Interesting question, similar to my case. Could you check one of the spesial journal in .... (lets me check first....)

Badges
Science method

More Ganesh Kotnana's questions See All

Could anyone please help me in finding the corresponding motion of the mode around 114 cm-1 for HoCrO3 compound ?

Hi, I am currently working on HoFe1-xCrxO3 compounds. I took raman spectrum for HoCrO3, and found there is a peak at around 114 cm-1. But from literature (Journal of Magnetism and Magnetic...

01 February 2017 884 2 View

How to calculate the error in the lattice parameter for an orthorhombic system?

error calculation in lattice parameter

03 April 2016 6,108 5 View

I tried to find ferromagnetic fraction using M-H loops for a RCrO3 sample and got negative value. Can anybody please help me what it resembles?

I tried to find ferromagnetic fraction using M-H loops for a RCrO3 sample and got negative value. Can anybody please help me what it resembles? Thanks

01 February 2016 1,073 5 View

How do I draw the photocurrents from a PSD (position sensitive diode)?

Is there any circuit? I have a DuoLateral PSD to measure magnetostriction? Not a cantilever deflection method

04 May 2015 1,435 2 View

During refinement using GSAS-EXPGUI, I got negative values for "shft" . Can I get negative values?

I got positive values for "asym" in profile parameters

02 March 2015 8,663 5 View

I am getting negative value for Uiso in GSAS-EXPGUI. Can any one tell me how to refine atomic positions and to not get the negative value to Uiso?

01 February 2015 9,292 13 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,081 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View