Can Anyone suggest me on the methods to calculate the power dissipation of a simulated circuit in Tanner EDA?

More Saravanakumar Chandrasekaran's questions See All

What are the environmental and health considerations associated with the production, use, and disposal of NiO nanoparticles?

24 April 2024 3,584 3 View

Error in ansys meshing?

When i am doing meshing, i got an information message box " The selective body meshing is not being recorded, so the meshing may not be persistant on an update.if you wnat to record the order of...

23 November 2023 3,580 2 View

What are the current or emerging research areas in cybersecurity for health information systems?

Upto my review till now on this area i have categorized papers Authentication protocol's for HIS Cyber Threat Intelligence IoT security Information Security Management

26 October 2023 1,421 3 View

Ansys fluent, I Can validate Flow Properties but not thermal properties in same proplem. Why?

I am trying simulation on natural circulation loop. when i am validating paper, all flow properties like mass flow rate, density and radial velocity is exactly matching with article. but when...

26 September 2023 7,888 4 View

What is curvature correction option in k Epsilon model in ansys fluent?

19 August 2023 9,270 0 View

What is Stabilizing pressure coupled to enhance linear solver Robustness in ansys fluent?

Sir, Why this problem coming in iteration? what actually mean? Some time it ends with few iterations after that it will become normal.

15 August 2023 4,310 0 View

Problem in ansys Fluent Iteration?

Hi friends, i am doing simulation on heat exchanger. when i am trying with Coupled algorithm, solution is easily converged. but when i am changing to PISO, iteration run for 24 iteratio(within...

11 August 2023 1,366 2 View

Error in ansys Fluent?

When i am proceeding in Run calculation in Ansys Fluent, it shows "Run Cannot be started until Validation issues are resolved " What it means? and how to resolve this issue?

10 August 2023 627 3 View

When simulating in Fluent, Continuity line in residual, moving in straight line, not converging, Why?

Hi friends, I am doing pipe flow simulation (supercritical CO2) in Fluent. I am trying for different heat input. all boundary conditions are same for all cases. three heat input values solution is...

01 August 2023 2,030 2 View

How to implement and verify 64 bit adder in zynq Zedboard?

I m trying to verify the 64 bit adder (verilog progam) in zynq zedboard 7000. but it has only 8 number of DIP switches and 8 number of LEDs only. How to verify the adder with 64 bits. ie 64 + 64 =...

04 July 2023 3,687 2 View

Are there any recent wearables for EDA/GSR measurements (possibly measuring skin temperature, heart rate, etc. as well)?

As Empatica E4 EDA/GSR wristband is discontinued, we are looking for a new device that can be used for scientific research. Ideally, a wristband and no electrodes since we would like to use it in...

09 October 2023 9,133 1 View

How to perform Energy Decompostion Analysis of an open shell system?

Want of to perform EDA of an open shell system, Pu(NO3)4.2H2O, here Pu has 4 unpaired electron. Please provide a detailed answer with a procedure of preforming the same in ADF.

08 October 2023 9,223 0 View

When did John E. Tanner was born?

Hi guys, I am preparing a presentation on diffusion NMR, where I introduce great names on NMR, such as Hahn, Purcell and Stejskal. I can`t seem to find much information on Dr. John E. Turner Jr...

07 August 2023 4,488 1 View

How can I do energy decomposition analysis (EDA) using gaussian g16?

I want to energy decomposition analysis in gaussian16, I am using the pop=NEDA keyword, however it is not working.

02 July 2023 8,723 0 View

Why stacking in pull down network saves more leakage power than pull up network?

Why NMOS stacking is more effective in saving leakage power?

04 June 2023 5,559 0 View

How leakage power is related to the operating frequency of the system?

Is system operating with low frequency dissipates higher leakage power than system operating with high frequency?

28 May 2023 6,733 3 View

What are the applications where SRAM and flip-flop/latches both are used?

Both SRAM and Flip-flop are volatile memory element. Is there any applications where both are used?

05 May 2023 7,435 1 View

SAPT EDA for trimeric systems?

I am trying to perform SAPT EDA calculations for trimeric (host-guest-host) complexes. I am using psi4 for my calculations. Now the problem is that psi4 is showing memory error due to the large...

24 January 2023 2,787 0 View

How to applied input with different switching pattern to calculate power dissipation in latches and flip flop?

How to calculate the power dissipation for different switching activity in sequential elements?

11 January 2023 9,468 3 View

X-ray Fluorescence Exploratory Data Analysis?

Does anyone have a good approach to using EDA for XRF purposes? I intend to apply EDA techniques in systematically sampling rocks, i.e., every 9 m or 3m inside the reservoir in a drilling context....

04 December 2022 9,824 2 View

Samuel Pagliarini

Tanner has a suite of tools, not a single tool. Assuming you are using tanner t-spice, all you need to do is to observe the current over time.

Jagdeep Kaur Sahani

use .power ( ) command or check hspice manual

Tajinder Kaur

you can try .power command in tanner s-edit file then you can see the results in output log file

Saravanakumar Chandrasekaran

Thank you all for your answers...