Can biosynthesised nanoparticles be lyophilized?

I am working on the biosynthesis of nanoparticles from actinomycetes. I need to know whether the synthesized nanoparticles be lyophilized to use for further applications?

23 February 2020 3,330 3 View

Miss classification in Image Binary classification?

I had Trained data of various images of truck tyres using the CNN model to classify whether the image is a good tyre or Bad tyre. When I am giving non-tyre image to my model, the model is...

10 February 2020 2,609 3 View

What is the cost to establish seaweed tissue culture lab in India?

To establish a seaweed tissue culture in India what is the total investment required. What are the primary things required and what is the scope in India in future?

26 December 2019 9,019 3 View

Fatal error: Atomtype CG3C51 not found -Gromacs?

While running protein-ligand complex md simulations after running genbox -cp complex_newbox.gro -cs spc216.gro -o complex_solv.gro -p topol.top i am getting error like.. Fatal error: Atomtype...

07 November 2019 439 3 View

How to modify silica nano particles before adding to PMMA solution?

18 March 2019 214 4 View

How to run deep learning algorithms on neo4j?

I had done semantic similarity to identify duplicate questions in data set using LSTM networks in python jupyter notebook. Now i want to do this task on neo4j to build knowledge graphs.

23 January 2019 3,297 3 View

Would like no know Ozone transfer rates into filtered water ?

I have a ozone generator 500mg/hr capacity i want to achieve 2ppm of dissolved ozone in 10 litre water can how much is the transfer rates of ozone & how much time it will take for the...

05 January 2019 8,104 2 View

What bioinformatic tools can I use to identify probable hnRNP regulatory sites in mouse GOI mRNA?

I am looking at alternative splicing in mouse mRNA and would like to identify if there are any heterogeneous nuclear ribonucleoproteins (hnRNPs) binding sites that influence the splicing events...

04 December 2018 4,331 2 View

What are the minimum requirements to setup a Gait lab for research purpose in an institute with optimum cost?

I want to setup a Gait Lab for my research work. So I need help for requirements of gait lab. i.e., i) How many cameras required and which company? ii) Force plate company, iii) Reflective...

18 September 2018 9,677 2 View

How to find out the annual and semiannual harmonics of time series data for an year?

I have a set of time series data for a single year (365 records). The objective is to calculate the anomalies in the values. However, anomalies are not defined as the differences from the mean....

09 August 2018 5,056 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View