Can anyone suggest a laboratory to check filteraction efficiency of a respiratory mask?

11 November 2012 0 3K Report

Need to check filtration efficiency of nano fibers for both biological and dust particles

Badges
Science topic

More Arun Karthick's questions See All

How to study atmospheric air?

I want to the study atmospheric air with respect to its content as well as with respect to its distrubution and its proportion. I want to know the instrument or any technique used regarding this.

11 December 2016 7,534 6 View

How to increase surface energy of nonwoven polypropylene?

I am using nonwoven polypropylene as support material to collect electrospun mat over it. The problem I am facing is the electrospun mat is not adhering to polypropylene due to its low surface...

09 October 2013 2,215 5 View

How to check the compounds present in Textile sludge?

I made an analysis with ICP, which gives metals present in it. How to check the compound of those metals present in textile sludge, e.g. instead of measuring iron (Fe) I have to measure iron...

07 August 2013 7,041 2 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

How can I immobilize Glutathione on to PCL electrospun nanofiber?

Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or...

18 July 2024 9,725 1 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

How to quantify fibrin formation for absorbent hemostatic biomaterial ?

I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...

08 July 2024 3,714 1 View

What does the area under the curve signify in dielectric loss tangent studies for solid polymer electrolyte ?

In solid ceramic electrolyte what is the Physical significant of area under the curve in dielectric loss tangent studies ??

23 June 2024 4,354 1 View

Why PLLA deposited by gap electrospinning lose piezoelectricity?

I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...

17 June 2024 9,763 0 View

Why after DFT energy calculation in dmol3 materials studio 2023, it does not give me the outmol file?

I used material studio app dmol3 module for geometry optimization for a nanotube, and then I calculated its energy, for some of gas phases and I actually had the outmol file which allows me to...

14 June 2024 5,636 0 View

Can anyone explain how mobile ions moves inside ploymer electrolytes?

I want to know the exact mechanism behind the motion of ions inside the polymer electrolytes.

13 June 2024 3,489 0 View