Can anyone please tell me (or refer to) the micromechanics of intraply or interlaminar lamina?

More Dheeraj Gunwant's questions See All

Hello everyone... Can anyone please give me some idea about the micromechanical modeling for intraply lamina for predicting its elastic properties??

I have already modeled RVE for single fiber lamina and determined its properties but wanna know how to model RVE for more than one fiber specifically in ANSYS APDL.

05 June 2016 5,241 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Raid Salih Jawad

Dear Sir

you can find your answer in this paper ,just loaded and open it.

http://nptel.ac.in/courses/Webcourse-contents/IISc-BANG/Composite%20Materials/pdf/Teacher_Slides/mod4.pdf

Dheeraj Gunwant

Thanx Dear Raid... I have already gone through these notes.. but could not get the desired answer. still searching for an elaborate source... I appreciate your effort! :)

Wenbin Yu

Please try SwiftComp at https://cdmhub.org/resources/scstandard, a general-purpose composite constitutive modeling software. It can deal with any microstructure including this what you have asked and provide material properties for any structural model including 3D solids, beams, plates and shells.