Can anyone please send me the complete simulation model of the paper which I am adding to?

More Debottam Bhunia's questions See All

Does ADRC controller provide sufficient robustness to external disturbances?

Actually, I want to compare robustness between ADRC & H infinity controller. ADRC is a sort of model free control whereas H infinity is model based. Suppose, a system is prone to cyber attack....

04 May 2021 3,776 2 View

Which one is having better accuracy in terms of reconstruction?

I want to compare accuracy among these four methods in terms of reconstruction. These four methods are mentioned below: 1. EMD (empirical mode decomposition) 2. DMD (dynamic mode decomposition) 3....

02 May 2021 3,894 9 View

How to export velocity data from MATLAB to TecPlot to plot the streamlines?

Streamline plots in MATLAB shows streamline only in the direction of the flow. But tecplot has options to plot in both direction. But Cant export data to tecplot.

09 October 2020 3,602 2 View

Is there any good journals which publish fuzzy group papers without fee?

Please provide some free SCI/SCIE/SCOPUS indexed journal for fuzzy group.

30 December 2019 6,138 1 View

Error in CHEMKIN file during flamelet generation. it says ""Unexpected word, , in CHEMKIN file, at line. no. 1"". How to get rid of this one?

Any idea is deeply appreciated.

17 September 2019 2,147 2 View

Can we calculate the reaction rate while using the non-premixed combustion model (which is based on mixture fraction theory) in Ansys-fluent?

For finite rate chemistry, the reaction rate can easily be calculated. However, the mixture fraction theory simplifies a combustion reaction into a mixing phenomenon, and the difficulties...

13 September 2019 1,970 3 View

What is the best way to represent/analyse proximity data?

Here my focus is to measure proximity (of group members) of free-roaming animals while resting. I collected data using instantaneous scans and now want to see the effects of seasons, human...

08 September 2019 399 2 View

How to calculate Genotypic and Phenotypic Correlations?

I want to correlate gene expression values of a same gene across different genotypes to check wheather the gene is closely correlate or least correlate or negatively correlate with the genotypes?...

09 June 2019 9,332 4 View

What is the minimum magnetic field needed to align the tip apex of a Cr-coated W-tip along the direction of applied magnetic field?

Our material of interest is Cr. So if I want to set the magnetization direction of the tip apex to a particular direction by applying an external magnetic field, then what is the magnitude of...

22 January 2018 6,930 1 View

How to remove the plasmid border sequence ?

When we over expresse one or multiple endogenous genes for improved trait we use plant expression vectors. There are so many techniques available by which we can remove the selection marker gene,...

15 January 2018 6,771 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View