What is the best way to conduct meta analysis ?

24 November 2020 1,318 8 View

How to create a Voltage Heat Map of distribution network?

I am trying to create a voltage heat map of a distribution network in Matlab/Python. I have the values of bus voltage magnitude and angle but cannot plot them in a heat map. The objective is to...

02 November 2020 3,561 6 View

Previously some data I have uploaded in mendeley data base and it provide DOI number. Can I published same data with another journal.Please suggest?

Previously some data I have uploaded in Mendeley database and it provides DOI number. Can I publish the same data with another journal ? Please suggest. Is there any problem of plagiarism with...

27 October 2020 2,801 6 View

If a system is stable in each of the operating regions, can it be said that the system is stable for the entire operating region?

If an operating region is divided into a number of sectors and if it is shown that the system is stable in equilibrium point corresponding to each of the sectors, can it be said that the system is...

21 March 2020 8,816 6 View

How to incorporate random uncertainty within the A-matrix represented by a gain block in Simulink?

I have a Simulink gain block that houses the A- matrix of the plant and I want to add randomness into the parameters of A-matrix. How do I achieve that in Simulink?

05 December 2019 6,127 7 View

How can one characterize anti biofilm mechanism of any phytochemical at molecular level ?

I have seen the antibiofilm effect of a phytochemical. It disrupts EPS but I want to know the mechanism of that agent at the genetic and molecular level . What experiments should I employ?

19 November 2019 1,139 5 View

What non-polarizing beam splitter should I use to split reflected light, but not the incoming one?

I am making a polar moke setup and need a non-polarising beam splitter which splits the reflected light but not the incoming one. I would be grateful for any suggestion regarding model number/...

14 November 2019 5,868 3 View

How can I ensure the stability of a MIMO system if all the individual subsystems are BIBO stable ?

If I have a MIMO system with a number of subsystems with moderate amount of coupling sensitivity and if those individual subsystems are BIBO stable then under what conditions the whole system can...

15 June 2019 1,363 4 View

Why over melted tracks (in laser remelting) arises with an increase in laser power while the increase in temperature is marginal?

In laser remelting of thermally spayed ceramic coating, an increase in laser power from 400 W to 500 W shows a marginal increase in temperature. However, the tracks shows a signature of over...

17 March 2019 2,354 4 View

Why does the inner radius of a Laguerre-Gaussian(02) beam go to zero at higher Laser energies?

I am doing some measurements using an LG02 beam and I find that the inner diameter is decreasing with increasing beam energy. This has already been seen. This means that the valley of the LG beam...

14 July 2018 8,939 9 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View