Can anyone help me use the TLM solver in CST?

Asmaa Zugari @Asmaa-Zugari

21 May 2014 1 3K Report

I want to use the TLM solver to calculate S11.

Anuraag Misra

prepare the 3D model and extract the eq ckt , that is exactly the TL M of the 3D model

Badges
Science topic

More Asmaa Zugari's questions See All

Strugglling with m6A dot blot any suugesstion ?

I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...

10 August 2024 8,539 5 View

What is the suitable solvent of MIL-100 for chemotherapy?

I synthesised a nanocarrier by conjugation MOF (MIL-100) with folic acid for use in chemotherapy but the samples didn't dissolve completely in aqueous solution or DMSO. Instead, they only...

19 July 2024 8,522 0 View

What is the suitable solvent of MIL-100 for chemotherapy?

I synthesised a nanocarrier by conjugation MOF (MIL-100) with folic acid for use in chemotherapy but the samples didn't dissolve completely in aqueous solution or DMSO. Instead, they only...

15 July 2024 2,414 1 View

What is the most accurate way to determine the energy gap of semiconductor materials? Is it better to use UV-Vis or PL measurements?

When preparing hierarchical zinc oxide ananostructure, the energy gap measured by PL was equal to (3.26 eV) While the energy gap value was determined by UV-Vis measurements (3.5 to 3.7 eV)

26 June 2024 7,505 6 View

What is the most accurate artificial urine recipe used in vitro for microbiological purposes?

I just found many protocols but not specific for bacterial growth

30 May 2024 6,305 2 View

How can I explain the acid base titration test for a PH responsive nanogel?

I have three nanogels.. The difference between them is the cationic monomer ratio... However, the test is giving me similar curve of the three formulations

27 May 2024 2,064 0 View

Question about XRD?

Hello, I was elaborating thin films from FeCl3 using a dip coater. These films were deposited on a glass sheet for 6 layers and then annealed at 500°C. However, XRD analysis did not yield any...

31 March 2024 9,413 3 View

Can I use two IRIS in the same plasmid expression cassette ?

I am trying to express m6A protein and a fluorescence one RFP in the piggyback vector. I was thinking first of using the P2A to separate between the m6A and the RFP protein but then I was afraid...

12 March 2024 9,713 0 View

How can I encapsulate cisplatin into a ph responsive polymeric nanogel?

I have synthesised a 100 nm sized cationic nanogel and I want to use it as a carrier for cisplatin and paclitaxel

03 March 2024 3,426 0 View

What tools needed to conduct areserch study about "burden of mothers in caring for child with colstomy" besides zarit burden interview scale ?

i'm preparing my protocol for master degree and it's my first time ,i need some help ,my reserch titel is "burden of mother in caring for child with colstomy"

02 March 2024 5,656 2 View

What should I upgrade in my computer to speed up simulation in CST?

I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...

10 July 2024 2,789 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

How do I get a graph along the line for the tangential and vertical components of the field in CST?

Hello everyone. I got slices of the fields by depth for each component (photo 1), now I want to get a 1D graph of the dependence of the electric field strength along the line, separately for the...

27 June 2024 5,466 0 View

Do you have any suggestions to illustrate the antenna design effectively except for CST, HFSS, FEKO, and Matlab?

24 June 2024 3,381 3 View

HI, How to find phase response in CST?

I'm simulating a metamaterial unit cell. I want to plot Frequency Vs Phase Response. Also I want to extract permeability and permittivity. Kindly share the steps.

23 June 2024 3,446 1 View

How can I get graphs of the normal and tangential components in HFSS?

Hello everyone. How can I get graphs of the normal and tangential components in HFSS? In CST it looks like this:

20 June 2024 3,131 3 View

How to obtain the scattered farfield in CST?

Hi, I performed a simulation of a Transmitarray structure with an impinging plane wave, designed to direct the output beam at 20° right with respect to the axe perpendicular to the structure. But...

19 June 2024 6,415 5 View

How to access Axis Marker Properties in CST Studio Suite?

How can I change marker axis line type to dotted in 1D Results/S-Parameters in CST Studio Suite?

10 June 2024 9,828 0 View