Can anyone help me to get fuzzy logic toolbox of MATLAB?

More Huda A. H. Lubbad's questions See All

Is there a matlab code that perform a data transmission through a wireless sensor network ?

I need the source node to broadcast a message to all nodes in the network. Thanks

11 December 2016 6,583 0 View

How can one simulate a wsn using simulink ?

Is there any paper or document ? Thanks Huda

10 November 2016 4,549 0 View

Which better in WSNs simulation OPNet or MATLAB ?

I want to simulate a wireless sensor network protocol. Include clustering then synchronized flooding to have constructive interference at the sink. I have to choose between matlab and OPNet...

08 September 2016 4,083 5 View

Is there any documents or book about how to program on Contiki os?

Can any one provide me with online documents or book about Contiki operating system.

04 May 2015 6,913 2 View

Can anyone help me to get contiki source code for Triggercast?

I need to make a constructive interference at one receiver from multi senders of sensor nodes. I found triggercast is the most accurate technique applied on Contiki Software. However, I didn't...

01 February 2015 8,801 3 View

How do you make time synchronization between WSN nodes to send the same signal at the same time in a real time testbed?

I am working on TI CC2530dk , using Contiki OS. I need two nodes to send the same signal at the same time to the sink. in order that the signals can be added at the receiver. How can I make the...

08 September 2014 6,016 3 View

In Wireless sensor network, how can we determine the ID of each node?

I need all sensor nodes to send the same signal to one node with ID=1. How can we determine which node is of ID=1.Thanks

08 September 2014 3,546 10 View

How can I use timesync.c in my contiki source code ?

I want to synchronize two sender nodes to send the same signal at the same time to one receiver. I use the collect example. how can i use the time synchronization protocol of contiki in my code

08 September 2014 7,599 1 View

I need a reference for calculating PRR or PER in WSNs?

Can anyone provide a reference or document for measuring wireless sensor network reliability using (PRR , or PER calculation) Thanks in advance Huda

01 January 1970 5,712 0 View

Is there any matlab code for PER calculation ?

I need to evaluate the reliability in a WSN by calculating the Packet error rate (PER) and PRR (Packet reception rate) using MATLAB Do anyone have a matlab code to calculate PER or PRR , or...

01 January 1970 4,747 0 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

Huda A. H. Lubbad

I requested a trial version from Mathswork, but they didn't reply me

Fréjus A. A. Laleye

you can download it here :

http://www.mathworks.com/matlabcentral/fileexchange/6434-fuzzy-logic-toolbox-add-on

Fernando De Lima Caneppele

Dear Huda A. H. Lubbad,

Try to get the program on student version for this link: www.mathworks.com/academia/student_version/

thanks Fernando, So I should buy.

Renann Baldovino

If you don't have MATLAB to create your FIS model, you can check and try fuzzylite to play with your model.

Thanks Renann. I will try it to use the fuzzylite

thanks alot Dr Ernesto. Actually I want to make clustering in Wireless Sensor Networks. is it possible to use xfuzzy for this purpose

Abhishek Jha

Dear Huda,

You can download the free version of MATLAB on softonic or getintipc sites. They provide pirated versions of the softwares.

Ali Baig

Hello,

i want to work on fuzzy logic toolbox in matlab but i am unable to do it.have you got overcome your problem if yes then please help me out.

facing some problem.......error below

command: which trimf

"C:\Program Files\MATLAB\R2017a\toolbox\fuzzy\fuzzy\trimf.m % Has no license available"

please suggest