08 June 2020 0 2K Report

I need 5 in-vitro model for Alzheimer's disease, I can be any animal model or human cell/tissue model but in-vitro

More Yash Kumar Vimal's questions See All
What is the physical significance of series resistance of a Schottky diode?

Is series resistance a parasitic parameter of the resistance of the semiconductor in a metal-semiconductor contact? Device physics

04 January 2021 5,544 3 View

Can we do FESEM of ZnO Nanowires without coating them with any conductive layer?

Nanotechnology, FESEM

13 December 2020 4,107 5 View

Do the anchoring condition at NP-LC interface changes in any particular solvent (i.e. toluene, ethanol etc) or remains the same ?????

For absorbance and emission measurements of nanoparticles dispersed nematic liquid crystal we dissolve sample into a particular solvent (like toluene, ethanol etc). do anchoring condition at...

04 December 2020 1,938 1 View

How can Gold be extracted from mining concentrates?

I work at a precious metal refinery. We extract gold using aqua regia. However, sometimes Gold does not dissolve in AR. Sometimes it precipitates due to cold weather? Is there a way to make sure...

07 August 2020 7,059 3 View

What will be the moment direction in vertical axis wind turbine?

I am working on the vertical axis wind turbine project. I have attached the picture in 2D. Wind direction is from negative X to the positive X direction. I applied 200 rpm in fluent and the...

17 November 2019 2,803 3 View

How to interpret Direct Aerosol Radiative Forcing (DARF) values?

I've calculated Direct Aerosol Radiative Forcing(DARF) values (W/m2) for Ahmedabad and Gandhinagar City, Gujarat, India using SBDART Model (AOD values as an input) at Top Of Atmosphere (TOA),...

22 October 2019 9,877 4 View

Why i am not ble to view bands on 10% and 12% SDS PAGE?

I am working on isolation of protein from stem of Nicotiana tabacum. I used protein extraction buffer and acetone precipitation method. From bradford assay, 1mg protein yield was found. 12% and...

24 September 2019 5,008 9 View

SSVEP signals are not properly generated. What should be the idle condition for SSVEP signal recording?

I have created the scenario with 4 red LEDs flickering with different frequencies separated by minimum 20 cm (at the side of monitor). The selected flickering frequencies sets were (6.25, 6.66,...

07 May 2019 5,352 1 View

How to calculate the weight of cement in M25 grade concrete of known volume?

Attempting to conduct a research inquiry on M25 concrete and was looking to validate a technique I found: Multiply the volume by 1.54 Divide previous value by 4 (since ratio of...

27 February 2019 7,494 5 View

What parameters influences permselectivity measurements?

In apparent permselectivity or Hittorf method for transport number measurements (3 x 30 min measurements per concentration) , a permselectivity of more than one was observed for commercial CEM....

16 January 2019 1,755 3 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close