Can anyone help me out with the simulation of wind turbine (torque and power output) rotor in cosmol?

More Praneeth Smk's questions See All

What websites or online resources are available for finding details of clinical-based research?

Websites or online resources dedicated to providing comprehensive details on clinical-based research are crucial for developing novel studies and should be identified

29 December 2023 1,422 6 View

Small particles are observed inside and around cells , what can be the reason ? Contamination or stress ?

These images are from Bone marrow hMSCs and gingival fibroblasts. There are small vesicles around the cells and also inside the cells. in hMSCs you can see once the vesicle density is high cells...

25 September 2022 7,008 0 View

How can i get a good intensity bands in native page?

i am performing an native page of my protein but i am not getting good bands can any one help me to figure it out

08 October 2021 9,228 6 View

Can I add a Link of an online Magazine Article to the Research Gate?

One of my research articles has been published in an online magazine. Can I add the link of that online magazine article to the Research Gate for sharing my research findings with other researchers?

09 October 2019 2,783 4 View

How can I interpret the Raman spectra of activated carbon materials?

The Raman spectrum of a sample (biomass derived carbon material) shows two sharp peaks at about 1340 cm-1 and 1580 cm−1, assigned to D-band and G-band, and two broad peaks at about 2100 cm-1 and...

05 September 2018 7,587 5 View

How to carry out random response simulation in NX?

I am unable to enter the input PSD data for proceeding with the solution. Any leads are appreciated. Please help?

28 August 2017 3,030 6 View

Any comments on the SEM analysis

this is the SEM image of a cement sample, I cannot see any variation in the phases such as C3S, C2S, C3A, C4AF. I did not use EPOTEK 301 as it is expensive and used araldite (epoxy and resign)....

14 June 2017 8,949 3 View

What is optimum quantity of carbonization of biomass with KOH activation for prolonged quartz tube life?

I am using tube furnace for KOH activation of biomass to get activated carbon at 800 C. I am facing the problem of frequent etching of inner surface of the tube in the active region leading to...

02 February 2017 689 13 View

How to see the change in material studio ?

i have an unit cell which is changing its dimensions and the atoms are moving the unit cell in dynamic load. So can i see an animation video on the material studio software. Is it is possible to...

11 June 2016 1,443 4 View

Can anyone suggest some standard books for learning NVH in Automobiles, analysis and their reduction?

I'm a Mechanical Engineering student passionate in automobiles. I would like to the explore the NVH Domain in automobiles. But because of lack of knowledge on the subject, I'm confused about...

16 October 2015 8,549 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there any instruments for studying time similar to the way it is in space?

There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...

06 August 2024 7,102 0 View

Gunwant M. Mule

You need to go through the simulations of stirred tanks in comsol. You will get some kind of idea on how to integrate forces over the blades. Thank you!

Eddy Gabriel Ibarra Ontiveros

Hi Praneeth, could you please tell me how you managed to calculate the output torque for your turbine. I've checked some documentation about modeling mixers and stirred tanks but I still don't know how to apply it to my Laminar flow simulation. Thanks in advance.