Is there any free software to simulate efficiency of thin film solar cells?

na

11 December 2017 9,364 0 View

Can anyone suggest me the absorbance spectra attached here is the spectra of of SnO2-Al2O3 nanocomposite?

The spectra has been taken by dispersing the nanocomposite in water

05 June 2017 6,789 2 View

Can anyone help me to calculate intensity in mW/cm2 from lux ?

11 December 2016 2,319 1 View

Can anyone give me the way to measure the absorbance of thin film deposited in steel substrate?

09 October 2016 9,574 0 View

Can anyone help me to characterize the pl spectra of In2S3 nanoparticle?

the spectrum is here attached for reference

08 September 2016 9,674 2 View

Can any one help me to draw the plot of transmission and reflection spectra from an absorption spectrum?

I have an absorption spectrum of ZnS nanoparticle.

02 March 2015 6,570 5 View

Can anybody help me to find out how to determine the cause of deposition of thin films on SnO2-coated glass substrates?

Chemical bath deposition.

02 March 2014 5,510 2 View

How is the band gap of a semiconducting material calculated from the UV-visible absorption spectrum?

see above

02 March 2014 8,250 8 View

Is there any change in the band gap of semiconductor when dye is deposited on it?

I am working on DSSC. it is required to explain the mechanism of change of efficiency of solar cell. Actually in my experiment the efficiency is increasing after deposition of dye.

01 January 1970 7,846 0 View

Where can I find a good free software to calculate the efficiency of shunt resistance series resistance from power output curve?

Where can I find a good free software to calculate the efficiency of shunt resistance series resistance from power output curve? I have the I-V data of chalcogenide thin films

01 January 1970 6,415 2 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

Do you know this error? The experiment was stopped by a potential overload on Vs (auxiliary electrode)?

Hello everyone Do you have any information about this error 'The experiment was stopped by a potential overload on Vs (auxiliary electrode)' in Origamaster software? I tried everything possible,...

19 February 2021 3,152 7 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View