Can anyone suggest me the absorbance spectra attached here is the spectra of of SnO2-Al2O3 nanocomposite?

The spectra has been taken by dispersing the nanocomposite in water

05 June 2017 6,789 2 View

Can anyone help me to calculate intensity in mW/cm2 from lux ?

11 December 2016 2,319 1 View

Can anyone give me the way to measure the absorbance of thin film deposited in steel substrate?

09 October 2016 9,574 0 View

Can anyone give me the circuit diagram to measure the dark I-V curve and power out curve for characterisation of pec cells?

09 October 2016 7,407 0 View

Can anyone help me to characterize the pl spectra of In2S3 nanoparticle?

the spectrum is here attached for reference

08 September 2016 9,674 2 View

Can any one help me to draw the plot of transmission and reflection spectra from an absorption spectrum?

I have an absorption spectrum of ZnS nanoparticle.

02 March 2015 6,570 5 View

Can anybody help me to find out how to determine the cause of deposition of thin films on SnO2-coated glass substrates?

Chemical bath deposition.

02 March 2014 5,510 2 View

How is the band gap of a semiconducting material calculated from the UV-visible absorption spectrum?

see above

02 March 2014 8,250 8 View

Is there any change in the band gap of semiconductor when dye is deposited on it?

I am working on DSSC. it is required to explain the mechanism of change of efficiency of solar cell. Actually in my experiment the efficiency is increasing after deposition of dye.

01 January 1970 7,846 0 View

Where can I find a good free software to calculate the efficiency of shunt resistance series resistance from power output curve?

Where can I find a good free software to calculate the efficiency of shunt resistance series resistance from power output curve? I have the I-V data of chalcogenide thin films

01 January 1970 6,415 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View