Can anyone educate me about use of predictive modeling in physiological research using a statistical software?

Dr (Professor) Biswajit Sinha @Dr_professor_Biswajit_Sinha

05 May 2014 1 4K Report

Use of statistical modeling in physiological research

Dear Dr Sinha - we have usually written the prediction analysis software ourselves. For example (attached) : Datta AK, Stephens JA. (1990) Synchronization of motor unit activity during voluntary contraction in man. J Physiol. ;422:397-419. SPSS allows writing of bespoke software and we have also used this for cosinor analysis of circadian rhythmicity. Hope this helps.

Badges
Science topic

More Dr (Professor) Biswajit Sinha's questions See All

Interested to learn Muscle Sympathetic Nerve Activity. Interested to undergo training. any possibilities anywhere?

Keen to learn muscle sympathetic nerve activity (MSNA). Any info from anywhere?

04 May 2016 3,503 0 View

What are the physiological journals published worldwide with good impact factor?

Physiological journals with good impact factor and do not charge any publication cost?

04 May 2016 2,592 2 View

How is hypobaric hypoxia different from normobaric hypoxia?

Are physiological responses same in hypobaric hypoxia and normobaric hypoxia?

04 May 2016 4,012 0 View

Interested to learn MATLAB?

Interested to learn MATLAB for HRV, BRS and BPV. Anyone to extend help within India or abroad?

04 May 2016 5,863 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View