What is the most suitable NMR solvent for carbon-based materials?

What is the most suitable NMR solvent for carbon-based materials?

25 December 2020 5,020 4 View

Effect of vibration on Heat transfer of fluid in pipe - COMSOL Physics?

We have a one meter long copper pipe through which water passes at a certain speed. The outer wall of the tube is covered by the heater where all the energy of the heater is transferred to the...

21 December 2020 8,954 8 View

Effect of adsorbent porosity on efficiency of adsorbent recovery ?

Hi guys. Can anyone answer the following with citing the references? 1) Relationship between adsorbent porosity and adsorption/desorption rate? 2)Relationship between porosity and adsorbent...

31 October 2020 6,323 5 View

Any recommendation for a good Machine learning course (with available materials for instructors)?

Hello everyone, I am looking for a good recommendation for a Machine learning course (with available materials). Which one do you suggest? Something that would be up to date with available...

15 September 2020 1,674 17 View

How to capture the geometry of rubble piles / collapsed structures beneath the surface via remote sensing?

Hi dear community, I am currently working on a project where I want to generate a 3D reconstructed model consisting of rubble piles (in consequence of a building collapse) via remote sensing. In...

10 September 2020 4,685 4 View

How can I insert an assembeled system, meshed by SOLIDWORKS, to ANSYS?

I already did it before but this time as the model is complicated I have faced with tis error: The surface mesh is intersecting or close to intersecting,making it difficult to create a volume...

05 September 2020 9,558 1 View

Raman peak shift or uncertainty?

Good day, I have a Raman spectra for 4 samples including Graphene oxide (GO) and its nanocomposites. According to the attached figure can sb tell me whether the different peak positions of the...

15 June 2020 6,467 8 View

Anyone in kolkata working of LNCaP prostate cells?

I am working with prostate cancer cells, i want to know who is presently working with PCa cell lines in viro and in vivo in kolkata.any leeds will of great help.

07 March 2020 7,831 1 View

How to model a fluid-structure interaction (FSI) Hyperelastic beam?

I am trying to model a fluid-structure interaction (FSI) Hyperelastic beam in COMSOL Multiphysics. The model works fine for low inlet flow velocity like 0.016 [m/s], but it gives the error below...

02 February 2020 3,394 3 View

How ferroelectricity may affect the photovoltaic performance in Perovskite solar cell?

how ferroelectricity can improve the efficiency of solar cell and what parameters are important in this relation?

01 February 2020 8,331 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

Which software is best to analyse multi-phase fluid flows ?

Hello everyone, hope all is good. I want to analyse multi-phase fluid flow through pipe, which software is best to do so ?

21 February 2021 4,230 8 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

How to compare different models with different inputs and data length?

I want to run 5 different models to estimate stream flow. In order to optimize the characteristics of these models I use Taguchi method. So I have to run different models according to the Taguchi...

11 February 2021 7,986 6 View

Examples of GAMS syntax for a permutation flowshop scheduling problem?

Hi everyone, I am new to the field of industrial engineering. I need to formulate a gams model for a permutation flowshop scheduling problem. I will appreciate if someone can send me a code...

09 February 2021 891 2 View

Does Abaqus plugin AM-Modeler predict the same temperature/crystallinity history as UMATHT user-subroutine?

During AM process, progressively activation of elements can predict the temperature/crystallinity history, including surroundings heat losses and than this data could be used to determine the...

06 February 2021 4,686 1 View

No title

29 January 2021 2,623 1 View