Bonferroni or Holm correction?

Miyuru Bandara Gunathilake @Miyuru-Gunathilake

20 May 2023 0 10K Report

Any one familiar with Bonferroni or Holm corrections?

Badges
Science topic

Similar topics
Correction

More Miyuru Bandara Gunathilake's questions See All

How can I remove salts from crude seaweed extract (except dialysis)?

Hi, I am interested to obtain phenolic fractions from crude seaweed extracts (using ethanol) and test for their antioxidant properties. Since most of the in-vitro antioxidant assays are...

26 January 2021 3,889 5 View

NetCDF to Table View option in Multidimension tool in ArcGIS results are not visible?

I am working on future climate projections. I need to extract CORDEX data at specific rainfall and temperature stations. The option "MakeNetcdf to table view" in Arc GIS is not showing results...

05 August 2019 9,496 3 View

What are the common reasons that authorship is granted to people who have not substantially contributed to a research?

Please share your thoughts.

07 August 2018 2,560 4 View

Do you believe that there is a correlation between rubber tack & viscosity of the compound?

20 October 2017 3,127 3 View

What are the basic factors to dissolve solid material in liquid hydrocarbon(eg- Octane)?

Hii all, Let me know factors that should consider when preparing a solution with a resin chemical(solid) and Liquid petroleum(Octane). Thank you.

12 October 2017 6,026 4 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View