Assigning ABS material properties in ANSYS?

06 June 2018 1 9K Report

Hello, I need to assign ABS material properties in ANSYS. What information should I need to include in the material properties section? Should I assign nonlinear materials? If yes, which one should I select in ANSYS?

Arielle Miller

ANSYS 19.1 Engineering Data, Granta Design Sample has an ABS plastic, but only linear elastic properties.

Badges
Science topic

More Abdullah Al Masud's questions See All

THUMS musculoskeletal model and LS DYNA?

Is LS DYNA only software for the structural analysis of THUMS musculoskeletal models? Can I use ANSYS or ABAQUS insted of LS DYNA?

04 May 2018 1,529 0 View

Need a human musculoskeletal model?

I need a human musculoskeletal model with appropriate muscle, bone and skeleton details. The model will be used in FEM software such as ANSYS, LS DYNA. How can I source such kind of model?

04 May 2018 5,327 4 View

Human Cell Vibration

Can anyone provide me suggestion on the following questions? Do cells under vibration present different behavior in the following conditions: in human body (within tissue, cells are like packed...

01 January 1970 6,901 0 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Look for qualified candidates of Visiting Scholars to Southwest Jiaotong University?

We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...

20 July 2024 1,165 1 View

How to combat antibiotic resistance?

The increasing resistance of bacteria to antibiotics has made many infections difficult to treat, posing not only a threat to public health but also a major challenge to healthcare systems worldwide.

18 July 2024 6,688 3 View

How to prepare bacterial conditioned media to study the effect of bacterial secretome?

I would like to investigate the effect of bacterial secretome on cancer cells. How do you prepare conditioned media from bacteria?? conditions- time points - media I am looking for the best way...

17 July 2024 3,785 9 View