Why are there two reduction peaks in my cyclic voltammogram?

When I measured the cyclic voltammogram of palladium in the pbs solution, two reduction peaks appeared. This did not match the literature I saw. Why? And how can I find the possible reaction...

20 February 2021 2,486 3 View

How to measure temperature and humidity in a gel environment?

One of my project requirements is to measure temperature and humidity in the growing environment of plant. The plant will be grown inside a petri dish with nutrient gel. A waterproof temperature...

28 January 2021 9,415 2 View

How to combine multiple LEDs with different wavelengths to create a uniform illumination?

Hello, I'm a university student who is currently doing a plant incubator project, which requires LED grow light system. One of the project objectives is to provide a wavelength-tunable light...

25 November 2020 5,508 6 View

How do I apply a constant load with same velocity to reach desire deformation in ANSYS Workbench?

I'm currently working on my academic project and it is required to perform a simulation about ASTM D575-91 (Method B) using ANSYS. I'm totally new to ANSYS, hoping someone can help me out. "The...

28 October 2020 8,764 3 View

Can we assume the water bottom reflectacne does not change and remain at a certain value?

Hi guys, I am trying to understand if the water bottom type does not change, its reflectance at a certain wavelength changes or not?

15 October 2020 6,297 3 View

What is the physical meaning of the cross term of the index performance of LQR ?

Dear All : I have a curious question. Among the index performance of the LQR, X' Q X and u' R u have the physical meaning. Now, my question what is the physical meaning of the cross term X' S...

02 August 2020 1,780 1 View

Extracting surface area, volume and cortical thickness from multiple groups using FreeSurfer?

Hello everyone, I'm new to FreeSurfer and this question might sound a bit stupid: I'm trying to get the volumetric measures, surface area and cortical thickness of brain regions of three groups...

29 July 2020 8,574 3 View

What is the function of sucrose or mannitol in buffer for cell lysis?

In the subcellular isolation experiment, sucrose and mannitol is present in buffers for resuspending cell pellet after centrifugation. For example, Isolation buffer (IB): 220 mM d-mannitol, 70 mM...

28 May 2020 4,608 3 View

UPLC-MS problem after MS was accidentally powered off ?

Dear everyone: We have an Acquity-UPLC coupled to Synapt g2-si MS system. Recently, the MS was powered off because the electricity supply failed. When I restart the MS, and then run LCMS samples....

09 March 2020 9,496 1 View

How to use pilot data to do simulation to calculate the sample size for linear mixed model using matlab?

Hi, all, I have a 2(group)*3(time) design, and at this moment, I got 5 subjects in each group in the pilot study. I would like do a power analysis and sample size calculation. since the design I...

03 February 2020 8,851 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to access MSCI KLD Stats and Sustainalytics?

Hello all, I'm currently working on my undergraduate thesis and I'm having difficulties trying to access KLD Stats and Sustainalytics because my campus Airlangga University and apparently other...

02 March 2021 8,525 1 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

How can we calculate the sample size for rodents for a particular period of time?

How can we calculate the sample size for rodents for a study for one year? Are there any specific protocols to be followed for designing rodent sampling? How long should be the sampling interval...

01 March 2021 1,056 3 View