I am looking for tutorials (videos or papers) associated with pool boiling heat transfer using Ansys Fluent. Thanks in advance.
Thanks Mr. Mohammed for the materials.
Hi,
have a look at these too, I'm sure they can help you
cheers
http://www.ijerst.com/ijerstadmin/upload/IJEETC_54d349d3b48f4.pdf
http://iicbe.org/upload/2831C0615016.pdf
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?
25 February 2021 7,187 3 View
I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...
21 February 2021 7,128 3 View
Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.
20 February 2021 8,271 3 View
I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...
19 February 2021 5,872 3 View
Dear colleagues, I was just wondering if you can suggest a good method to get a rough estimation to the concentration of O2 and H2O inside the glove box as unfortunately, our glove box doesn't...
17 February 2021 1,012 3 View
Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....
13 February 2021 3,261 3 View
Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...
06 February 2021 3,520 3 View
Hi all, Currently, I electrodeposited polypyrrole on carbon electrode but I got some problem when polypyrrole also deposited on the surface of the counter electrode. The concentration of pyrrole...
05 February 2021 2,103 3 View
Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...
03 February 2021 6,853 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...
01 March 2021 7,168 9 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?
01 March 2021 9,785 3 View
I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...
01 March 2021 8,415 1 View
I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...
01 March 2021 6,450 5 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...
28 February 2021 4,868 2 View
Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...
26 February 2021 6,253 3 View