Any suggestions on ball milling of lanthanum and steel?

04 April 2015 1 685 Report

if anyone give me an atricle for the lanthanuma nd steel by ball milling and there caracterisation by TEM SEM VSM DSC MOSSBAUER?

Samira Lalaoua

thank you Mrs Ariadne Tsambani FOR YOUR ARTICLE but i work about Fe/La2O3

Badges
Science topic

More Samira Lalaoua's questions See All

I need the point CIF of somme element?

I have difficulty finding the atom positions of some elements such as Fe, La2O3, Y2O3, LaFeO3 i need that for fitting my XRD spectra?

01 February 2016 5,132 1 View

What is the lanthanum oxide structure?

I did the mechanical grinding of lanthanum oxide but I had an obstacle to determine the probable structure of this oxydeau. At the beginning I found at least three different structures. After...

01 February 2016 2,490 6 View

Please can anyone teach me the programm maud i dont found who can help me?

programm maud ? WHO CAN HELP ME?

08 September 2015 7,062 0 View

Can any one give me how fabricate or produce the ODS steel; and there proprities?

ODS the technique used to produce the ODS and the proprites of ODS ?

04 May 2015 2,396 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

How to model steel jackets using SeismoStruct?

Hi all, Does SeismoStruct support modeling rectangular RC columns retrofitted with steel jackets (e.g. rectangular, elliptical) ? Any suggestions for other software (apart from...

20 February 2021 4,521 1 View