Any one interested for collaborations (Selective Laser Melting (SLM) of Nickel- and Titanium-based alloys)?

More Aleksei Obrosov's questions See All

How to apply electrochromic WO3 films to ITO glass using reactive magnetron sputtering?

How to obtain an electrochromic layer of tungsten oxides of the stoicheometric composition WO3. What are the optimal deposition conditions?

13 December 2023 3,226 3 View

Graphite is an conductor of electric current or a semiconductor ?

Graphite is an allotropic modification of carbon, therefore it is a non-metal. In general, non-metals do not conduct electricity. Carbon is from the same group as silicon and germanium. It can be...

18 April 2023 4,776 3 View

Can WO3 films be used as a pseudocapacitive electrode material for supercapacitors?

WO3 films reversibly include Li, H, Na, K ions from different electrolytes into its structure without changing the structure. Some metal oxides have been proposed that can be combined with...

19 June 2021 303 3 View

Is it possible to mechanically activate carbon nanotubes and How to do it?

It's necessary to increase the thermal and electrical conductivity of multi-walled carbon nanotubes (MWCNTs) obtained by the CVD-method. In this case, MWCNTs are used for electric heaters and the...

17 May 2021 1,529 3 View

How to solve contact problems? Why zero VOL. FLUX is everywhere during simulataions in Abaqus/CAE?

Hello everybody, Could somebody help me with my simulations? I'm trying to do a nonlinear static simulation in 3 steps in Abaqus. Let me tell you a bit more about my simulations, my goal is to...

12 July 2020 549 3 View

Do someone know how to get cross section for different reaction from LEND physicslist in Geant4?

I am trying to get cross sections for photonuclear reactions (gamma, n). So I have gamma beam with energy from 0.1 MeV up to 50 MeV and gold target. And I want to get cross sections for the next...

17 March 2020 1,561 3 View

Any one interested for collaborations (FIB sample preparation for TEM investigation)?

Our group is working with different coating systems and materials. We need somebody, who can help us to do FIB sample preparation. We are planning to wirite few publications. Sharing authorship...

27 November 2018 9,898 3 View

How to interpret the DSC analysis of Zr1Nb alloy with and without additional element??

We have Z1Nb alloy and provided DSC analysis with and without additional Ti. We found that alloy has two transitions. The low-temperature transition, occurring between about 500°C and 650°C. The...

19 July 2017 6,196 1 View

Is it possible to use glycerol to DNA drying?

The storage buffer of the RiboLock RNase reagent contains 50% (v/v) glycerol that prevents the overdrying of RNA. My question is what if we would use ethanol along with glycerol for DNA drying...

06 October 2016 9,035 7 View

Any one interested for collaborations (FIB sample preparation for coatings after erosion and corrosion)?

Our group is working with coatings and we have done few erosion tests. We need somebody, who can help us to do FIB sample preparation for our coatings. We are planning also to do some corrosion...

07 June 2015 5,613 9 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

Interested in a SCOPUS collaboration?

Hi RG family. My team and I are working on some SCOPUS publications and we need co-authors who are willing and capable of undertaking both qualitative and quantitative-based studies. The scope...

02 August 2024 7,843 0 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

Is there any Indian Company or Startups, from any universiy or IITS, which manufacture Gas Chromatography instrument , i want to make a custOmized G?

or we can collaborate

01 August 2024 6,705 2 View

Have you heard about Technological Surveillance on Oceanographic Research Vessels?

It is important to highlight that technological surveillance on oceanographic vessels is a collaborative effort in which different specialists work together to effectively leverage technology in...

31 July 2024 1,633 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

Slim Kaddeche

I'm interested to work with you on this topic. Please send me more informations.

Best regards,

Yunhui Chen

Hi, Our research group is experienced with metal metallurgy and SLM. If you are interested, plz contact [email protected] for further information

Sonia I. G. Fangaia

I'm interested. Please send me more informations. Best regards