Any ideas as to why there is a non agreement within XRD and LRS results?

05 May 2014 1 8K Report

XRD and LRS analysis was done for finding corrosion products after a corrosion test on the surface of metal. But the XRD results are showing a compound which is not detected by LRS. What could be the reasons for this?

Zol Bahri Razali

Dear friend, very interesting question.

However, the easiest way is searching the related document by typing the keywords into google scholar. You will find some related articles.

If yet to find the articles, do not hesitate to let me know. InsyaALLAH I will help you in detail.

Good luck. Dr Zol Bahri - Universiti Malaysia Perlis

Badges
Science method

More T.P. Ismail's questions See All

Which is the best etchent for austanitic steel (304,316 Etc) to use in Replica metallography (Field metallography)?

etchant for insitu metallography or Replica metallography for austenitic steel.it found to be very difficult to find good and fast etchant to use in replica. I tried 1:1 HCl:HNO3, water based...

10 November 2016 753 2 View

Which is the best open source FEA analyser?

I would like to know the best open source FEA analyser for static and dynamic analysis.

31 December 2014 3,350 4 View

This is SEM image of martasitic steel(aisi 4340) fracture surface . Any idea what type fracture occured and waht type morepholigcal feature is this?

first image near to the beach mark area second image near to the fast fracture zone

01 January 1970 4,536 0 View

Is there any book to refer for microstrucutral analysis of boiler tubes(1Cr-0.5Mo steel, 2.25Cr-1Mo steel tubes)?

life assessment and creep analysis. microstructural changes in long term exposure to high temperature and pressure

01 January 1970 2,740 8 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,081 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View