10 October 2017 1 10K Report

i find many differents way but nothing clear

More Yusdel Díaz's questions See All
Someone has some information about the optimization of the steel refining process in a spoon oven?

someone has some information about the optimization of the steel refining process in a spoon oven

31 December 2017 9,427 0 View

What is the best way for rolling steel process modelling?

what is the best way for rolling steel process modelling?

11 December 2017 9,825 4 View

Anybody have a study about a determination of sulphure in molten steel?

anybody have a study about a determination of sulphure in molten steel?

11 December 2017 5,951 1 View

Someone has some information about the kinetics in the process of obtaining resulfurized steels?

someone has some information about the kinetics in the process of obtaining resulfurized steels?

11 December 2017 8,218 0 View

Any way for use montecarlo methods in nonestacionary heat transfer?

any way for use montecarlo methods in nonestacionary heat transfer?

10 November 2017 5,503 3 View

What do you think about the specimen creation in solidification of steel?

what do you think about the specimen creation in solidification of steel?

10 November 2017 3,786 0 View

Chemical energy aproaching in Steel AEF?

someone can help me get some study related to the breakdown of chemical energy in steel furnaces for the production of steel

10 November 2017 9,020 0 View

How i can obtain any elastoplastic model in steel solidification?

how i can obtain any elastoplastic model in steel solidification?

10 November 2017 9,590 0 View

Some model to optimize the amount of coating of copper electrical conductors"?

some model to optimize the amount of coating of copper electrical conductors"?

10 November 2017 8,418 0 View

What is the most way by studies in modelling of heat transfer in continuous casting steel ?

what is the most way by studies in modelling of heat transfer in continuous casting steel ?

09 October 2017 606 2 View

Similar questions and discussions
How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

¿Are oxygen vacancies in semiconductors capable to change the band gap?

Dear all! Oxygen vacancies do raise negatively the Fermi level by increasing the negative charge in the semiconductor crystal structure. In the case of n-type semiconductors, I wonder if this...

30 July 2024 8,339 2 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Seeking recommendations for equipment to mimic sunlight and heat up a greenhouse system?m?

I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...

28 July 2024 4,006 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close