Any body using super critical fluid extraction for analytical sample preparation?

09 September 2011 1 1K Report

Please tell me the Make/Model of super critical fluid extraction apparatus which can be used for analytical sample preparation.

Thanks

John Douse

www.supercriticalfluids.com/prod100.htm (SF Technologies USA).

www.waters.com

Badges
Science method

More Senthamizh Selvan's questions See All

What is the cell used in volumetric karl fischer titrimetry?

Galvanic Cell or electrolytic cell ? What is the detection technique?

08 September 2012 4,260 2 View

How to prepare and increase yield for acetal synthesis?

I am mixing some chemicals along with propylene glycol with some aldehydes, in some instances there is a formation of acetal but other times not. Does anybody know the thermodynamics & kinetics...

07 August 2012 5,975 2 View

Which is the precise ionization and %area is close to absolute % between MS ionization (GCMS) and FID ionization (GCFID)? Why?

Are the % area of TIC of GCMS and FID comparable? if not why? What is detector linearity? i worked with absolute % (Pharma) of sample composition and also % area composition (in CRO, Synthetic...

09 October 2011 7,741 3 View

How to prepare sample & analyze a volatile content in beverages?

I need to compare two products of same brand by GC / GCMS, i have tried to extract the volatile part of the aqueous beverage by using CH2Cl2, pentane:diethyl ether; but the volatile are very less....

09 October 2011 2,176 6 View

Anybody using "Y" Splitter for GCMS?

I am using 'Y' splitter for our GCMS, it connected tat column outlet and one part is going to MS and another is going to FID; i have a sensitivity problem in FID and RT differences ( TIC-MS is...

08 September 2011 4,723 7 View

What are retention indices in GC, GCMS?

08 September 2011 3,574 11 View

Is it possible to utilize an old Gas chromatograph “HP 5890 with auto sampler" effectively?

It is having GPIB Communication; old data acquisition software-HP Chemsation. data analysis is not so good. Sensitivity of the instrument is in question. How could I utilize the instrument...

08 September 2011 1,340 1 View

Anybody knows about automated volatile oil determination methods?

We have a classical method of analysis to determine volatile oil in the natural products. It is time consuming- taking 4 hours. How can I improve the tech? Many thanks

08 September 2011 1,867 2 View

It is better to be roughly right than precisely wrong. —John Maynard Keynes

It is better to be roughly right than precisely wrong. —John Maynard Keynes You all have probably heard the story about Malcolm Forbes, who once got lost floating for miles in one of his...

08 September 2011 2,573 2 View

Anybody using gamma spectrometer?

What is the use of it.

08 September 2011 6,564 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

EDC carbodiimide and NHS easter 's half life among different pH?

It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...

25 July 2024 8,738 0 View

How to determine method detection limit in an analytical method?

I know the difference between instrumental LOD and method LOD but my query is - in case of any sample whose concentration is zero or not detected by the instrumental LOD, is it possible to get...

24 July 2024 6,592 5 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

How to eliminate the carry-over effect in GC-MS/MS system?

Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...

22 July 2024 5,492 6 View