Ansys Maxwell Induction Coil Gun?

14 April 2021 0 7K Report

Which steps do you think wrong or missing at the given project? I m doing all of them step by step but my force and speed graphs are not meshing.

https://www.programmersought.com/article/81474266082/

Badges
Science topic

More Çağdaş Tunceroğlu's questions See All

Has anyone cloned shorter plasmid than expected?

I have been cloning TOPO vector containing 3'UTR of my gene of interest into pmirglo vector (7350 bp). I digested pmirglo and topo vector with XhoI and SacI and ligated them. I also digested...

14 May 2018 8,902 3 View

Has anyone cotransfected a plasmid containing 3'UTR of gene of interest and another plasmid expressing miRNA sequence to HEK293T cells?

I cotransfected HEK293T cells with a plasmid containing 3'UTR of gene of interest and another plasmid containing miRNA sequence. I used equal amount for these two plasmids. After I did luciferase...

24 December 2017 5,936 1 View

Has anyone use infusion cloning to insert short DNA into a vector?

Hi, I want to insert 130 bp DNA into 3000 bp vector, however I could not obtain colonies. I used 50 ng insert DNA and also tried to increase insert amount but still I could not observe any...

10 November 2016 3,279 5 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Is it necessary to report effect size (ES) in statistics of biomedical research given that we already report p values routinely?

Pls share your thoughts

01 March 2021 7,330 4 View

Which reagent is best among 'Dimethylglyoxime" and "Dithiothreitol" for spectroscopic determination of Nickel ?

What I think is Dithiothreitol. As it is water-soluble and does not form a precipitate. But, the thing is it contains sulphur which is quite hazardous to aquatic animals.

01 March 2021 8,374 4 View