05 June 2020 1 3K Report

Hello,

I am running a 3D density based transient problem with Spalart-Allmaras turbulence model. After few iterations I am getting Negative Nut in xxx cells. I tried to search the cause, but not successful in finding answers. Could anybody help me in understanding from where this problem arises?

More Naveen Shirur's questions See All
Can anyone explain how to calculate encapsulation efficiency(Plant extract encapsulated alginate nano particles) using total polyphenol content?

Please suggest me if there are any reference materials for this topic. Thank You

30 December 2020 3,799 2 View

Electric field inside a biased N-type uniformly doped semiconductor?

What does the profile of electric field look like in a uniformly doped N-type semiconductor when an external voltage of 'V' volt is applied? Please provide any reference material if possible.

06 November 2020 1,987 8 View

Plane stress or plane strain for Railway Ballast system ?

Dear All, I am working on a wooden rail sleeper analysis. Using the Druker Prager model for Ballast and soils, Initially, I assumed the 2D Behavior of RailSleeper and Rails was Plane Stress and...

04 October 2020 5,459 8 View

What should be Optimum Review duration for a research/review article for any [unpaid/freely publishing]journal till acceptance?

Dear Research Gate Members, We all have experience regarding publications of research/review articles in various journals. Some of the journals review the articles in 4-6 weeks and some takes...

01 October 2020 7,201 1 View

How to write an impressive review paper in the field of Industrial effluent treatments?

I am currently working on collecting literature based on the available treatment technologies for industrial effluents. There are vast variety of methods physical, biological and Advanced...

23 September 2020 2,314 4 View

Fibrous rock with triclinic symmetry?

I am working on wave propagation in fiber reinforced material. Please provide me an example of rock-type which is consisting property of fiber and exhibiting triclinic symmetry with its elastic...

20 September 2020 9,874 1 View

How to pursue modelling and map Traditional Knowledge?

I was wondering is it possible to map Traditional Knowledge (TK) of a bigger region (say staus of TK) on the basis of sampling in a smaller region through Arc GIS and modelling? Say we sampled in...

13 August 2020 308 3 View

Pressure behavior from CFD simulation and testing?

Hello, I am simulating gas flow from a high-pressure (700 bar) to a low-pressure container as shown in the attached figure. The red curve shows the pressure curve obtained from the testing, while...

04 July 2020 2,077 2 View

Ansys Fluent remeshing on hex mesh?

Hello, I went through ansys fluent dynamic meshing guide. It says remeshing can be done only on tetrahedral mesh. I still tried to implement it on hexahedralmesh. It works well. It is bit...

03 May 2020 2,677 4 View

How AI and Deep Learning can help to Screening Corona virus (COVID-19) ???

There are many Articles out there related with Deep Learning with corona virus, For Example : "deep learning algorithm using CT images to screen for Corona Virus Disease (COVID-19), Deep Learning...

12 March 2020 3,780 9 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close