How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

SDS page software for analysis?

I did sds page to determine the difference in protein expression between 3 types of vaccine , but i don't have scanner or densitometer available. . so i wonder if there is a software to analyze...

02 March 2021 6,270 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View