Acid hydolysis kinetic for producing Cellulose nanocrystals (CNC) or nanocrystalline cellulose (NCC)?

More TriDung(T.-D.) Ngo's questions See All

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

While doing Chronoamperometry, when the light is turned off, why the current is not decreasing sharply?

Here, I have used Ag/AgCl as reference electrode and 0.5M KOH.

29 July 2024 4,538 3 View

Is it possible to dock more than one drug in the same active site or pocket of a protein to study synergistic/antagonistic/additive properties?

I wanted to know whether we can observe the synergistic/antagonistic/additive properties of combinations or mixtures of compounds through docking analysis. But during docking preparation any...

28 July 2024 7,413 6 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,330 0 View

Regarding green consumer behaviour ?

HOW TO WRITE GREEN CONSUMER BEHAVIOUR AS A LITERATURE REVIEW

28 June 2024 2,661 0 View

Can the atomic % and weight% of a doping element decrease with increasing its concentration in the resulting compound? If yes, then how?

I found atomic% and weight % of doping element decreased in the resulting compound on increasing its concentration.

28 May 2024 2,455 2 View

How to determine decision limit (CCα) according to CIR 2021/808?

CIR 2021/808 written as "the CCα shall be calculated as follows: Method 1: by the calibration curve procedure according to ISO 11843-1:1997 ( 14) (here referred to as critical value of the net...

13 May 2024 9,481 0 View

How do I perform a dose response curve and get IC 50 values for herbal extract powder?

I need to find out the desired dose for my poly herbal formulation. Please guide me how to get the figures

12 May 2024 8,290 1 View

CNN model and Multi-output regression?

Dear All, I have an imagery with a single fish species within each image along with a list of morphometric measurements of the fish (length, width, length of tail, etc). I would like to train a...

28 April 2024 2,090 2 View

How to calculate the stress of material using XRD data?

Is there any formula to calculate stress

20 April 2024 8,612 2 View

Is it possible to use a safer acid instead of monochloroacetic acid to convert bacterial cellulose to carboxymethyl cellulose?

Hi, researchers, Is it possible to use a safer acid instead of monochloroacetic acid to convert bacterial cellulose to carboxymethyl cellulose?

29 July 2024 4,570 0 View

Do the parts of the body that are situated at a longer distance from the central nervous system have the least control & coordination comparatively?

What would be the effect of distance from CNC cum Heart on the structure and function of a particular part of the human body? Do short people have evolutionary advantages to control body parts in...

09 July 2024 2,052 3 View

Is the use of microcrystalline cellulose MCC 102 in direct compression technology justified, given the low flowability of this excipient?

Hello everyone reading this topic! It is well known that microcrystalline cellulose 102 is recommended for use in direct compression technology, however, like other grades, it has poor flowability...

08 July 2024 2,807 0 View

How is the deconvolution area method applied to determine the crystallinity of cellulose using X-ray diffraction (XRD)? ?

I use X-ray diffraction (XRD) techniques to quantify the degree of crystallinity in my samples, referring to the following formula (CrI=Acrystal-Aamph/Atotal ). using deconvolution area methods (...

06 July 2024 6,234 9 View

Cellulose degradation rate in anaerobic digestion?

Hello, I am looking for (estimated) degradation rates of cellulose in a classic anaerobic digestion setup (meso or thermophilic, WWTP sludge, 30+ days of operation) to have an idea of the % of...

01 July 2024 5,867 5 View

Is water a good solvent for Non contact mode of Atomic Force Microscopy analysis of bacteria degraded lignin and carboxy methyl cellulose?

I am studying the surface topography of bacteria-degraded cellulose and lignin using the non-contact mode of Atomic Force Microscopy (AFM), which requires a solvent to make a dispersion of the...

21 May 2024 6,358 3 View

Can you suggest lab services in India for determination of cellulose hemicellulose and lignin content in plant biomass?

I want to know affordable lab services in India for the said analysis

13 May 2024 4,186 1 View

How to increase molecular weight or further polymerize cellulose triacetate?

Hi all! I would like to know if there is a method to polymerize low MW cellulose triacetate (e.g. re-engaging in acetylation). Or this is not possible and the MW of my cellulose source should be...

08 May 2024 5,260 1 View

Is this possible to make Nano Crystalline Cellulose (NCC) from Micro Crystalline Cellulose (MCC) of Jute Fiber?

I want to study the properties of Jute NCC. What are the changes, if I make this nano to micro?

01 May 2024 7,385 4 View

How to dissolve cellulose to get a transparent film? kindly suggest me a chemical to convert dissolved polymer into a gel or recommend a plasticizer?

18 April 2024 9,076 3 View

Janne Tapani Keränen

I'm not sure is this what you are looking for: http://www.sciencedirect.com/science/article/pii/S0144861715009959

or https://www.google.com/patents/WO2012127110A1?cl=en&hl=fi

TriDung(T.-D.) Ngo

Thanks Janne, any specific study on the rate of conversion from cellulose to CNC, reaction time, temperature, CNC yield, sugar etc during acid hydrolysis.?