Global change in protein expression?

Dear all, When I run my yeast total protein lysate extracted after 10 minute-treatment with my compound, I observe a global up regulation in proteins, even my loading control protein. I suspect...

03 January 2021 1,388 8 View

Molydenum Alloys Forging Process ?

Hello dear Academicians, I've been struggling on a specific subject for a while. Hence, I'd like to get some advice. I am working on Mo-0.5 Ti alloy production via powder metallurgy technic. I...

20 December 2020 3,805 2 View

Tetracycline/doxcycline treatment?

Hi all, I am not sure whether or not this question was asked. I wonder can I induce expression of my protein with tetracycline or doxycyxline while seeding cells instead of one day after seeding...

05 November 2020 2,417 4 View

How to distribute Titanium in Molybdenum host material via PM?

Hello dear Researchers, I've been working on to produce Mo-Ti alloys via powder metallurgy method. Yet, I've come across a problem: I can not properly distribute Titanium in Molybdenum host. I'm...

10 August 2020 4,502 3 View

How to distribute Titanium in Molybdenum host material via PM?

Hello dear Researchers, I've been working on to produce Mo-Ti alloys via powder metallurgy method. Yet, I've come across a problem: I can not properly distribute Titanium in Molybdenum host. I'm...

10 August 2020 5,909 4 View

How to peel off PDMS film from a glass petri dish without damaging it ??

I have prepared 15wt.% PDMS and poured it on a glass petri dish, then let it dry for 72 hr at room temp. after I tried to peel it and it doesn't work, so I am crosslinked in an oven for 3 hr , but...

26 July 2020 9,892 2 View

What is the best solvent for PVDF ?? Dimethyl sulphoxide or Dimethylacetamide??

For membrane preparation PVDF will be used , and I was wondering which solvent is the best for dissolving it, non-Toxic solvent , useful in dissolving other polymers such as PES, PDMS, Peba

05 July 2020 1,655 5 View

What is the best sintering temperature and environments for Zn-Mg alloys?

Hi everyone; I want to sinter Zn-3Mg compacts produced by powder metallurgy. The sample dimensions are d: 20mm and l:10mm. Could you please suggest to me the environment and temperature and time...

11 June 2020 2,922 10 View

How to count objects on the image with deep learning algorithms?

I am studying the first deep learning project. I need to counting tubules and cells. How to do this? If you suggest a tutorial (or another thing) related to this subject, I would love...

29 April 2020 989 7 View

Are there any good data-sets or research papers/code for Deep Learning Model for medical 3D Construction from 2D CT Images?

I want to create a Deep Learning Model for 3D Construction of Breast Cancer in CT Images. However, I cannot find an appropriate data-set or research paper. The data-set should be multiple CT scans...

04 March 2020 3,614 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View

How can I check similarity between two signatures?

I want to train a model that should predict if a given signature is a genuine or a forged one. The model should take two images as input. One is the real signature, and the other is to be...

11 February 2021 4,436 3 View

How can we quantify martensite in Ferrous and Titanium alloys?

How can we quantify metastable phases like martensite in Ferrous and Titanium alloys, in relation to their stable counterpart For example in EBSD, XRD, Optical? Eg, Martensite and Ferrite maps.

09 February 2021 7,572 3 View