3D model in Cupcarbon, is it possible?

Sergii Kushch @Sergii-Kushch

09 November 2018 1 2K Report

Dear colleagues,

I need to create WSN model in 3 dimensions. I tried to use Cupcarbon for it but I couldn't find this function there.

Could you explain me, how to do it in the package?

Or to advise other software where it is possible.

Thank you.

Sergii Kushch

Thank you for the link but it's not what I need.

I need to create a model of WSN for example:

- of the many floors building

- of a several level's smart city

where there are many nodes on each level or floor and there are connections between the levels too.

Badges
Science topic

More Sergii Kushch's questions See All

Spermine detection by HPLC?

I tried to detect spermine using reverse phase HPLC and a derivatization agent, but a peak that I want to see on the chromatogramm is very low and is not significantly different from the base...

17 June 2019 5,515 3 View

What are your opinions about perspectives of oxymoron like pathology diagnosis and treatment?

It’s known, that oxymorons are a proper subsets of the expressions, whose values mutually exclusive, and give us a semantic paradox. We proposed and tested algorithms for diagnosis of oxymoron...

12 October 2018 3,607 0 View

What are your opinions about perspectives of Moebius strip like pathology diagnosis and treatment?

Proposed and tested an algorithm for diagnosis of Moebius strip like pathology, as prerequisite for treatment correction. The algorithm is reduced to initialization of study objects as a...

12 October 2018 5,966 3 View

Where can I physically get a large library of protein genes?

I am studying massively parallel protein-protein interaction. Is there a good source for a ready DNA library, where a protein gene (or part of it) would be surrounded by standard adapters? Like...

05 July 2018 3,018 1 View

fluorescent voltage sensors use?

Dear friends, i have a question regarding the fluorescent voltage sensors. I never tried it before, so I need good advice. What is your experience with Voltage dyes? If would use the...

11 January 2018 5,622 2 View

Do you have a job opportunity in Blockchain area?

Dear colleagues, My current project will finish this December and I'm looking for a new job opportunity in a Blockchain researching area. Write me please if you have an open positions for...

17 December 2017 5,009 3 View

How can I calculate using of energy by WSN node?

Could you write a link where I can find formulas for calculation an energy which is used by node of WSN (for transfer a data)?

17 December 2017 7,814 14 View

What problems are there for implementation blockchain technology in IoT, WSN and mobile devices?

All know that there are a problem POW for small devices. What with what problems have you encountered when implementing blockchain for small devices? What criteria do you use for evaluate new...

12 December 2017 9,748 6 View

We are looking for blockchain researchers.?

Dear colleagues, We are looking for researchers who work with Blockchain technology for taking part in a program committee for Workshop on Blockchain Technologies and Security (BTS) of 9th...

10 December 2017 5,412 31 View

Has anyone specified the scattering coefficient for propane-air fire in Fluent?

I am modelling a 0.5 MW C3H8 fire in open air in ANSYS Fluent, need to account for soot and therefore set the Scattering coefficient. Combustion model - EBU (Eddy Dissipation model).

29 May 2017 4,530 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Hello all, Looking for international reviewer to review Ph.D thesis in wireless sensor network.Can anybody help?

My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...

07 August 2024 4,600 2 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View