30 March 2017 1 2K Report

Based on a journal that I read, CDI at constant voltage leads to having a shorter time in a given cycle when the system has reached its lowest effluent concentration.

My question is, what's bad about that? And how is CDI at constant Current any better?

Thank you!

More Karl Billy Geron Hiñola's questions See All
How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Has any research on translation investigated the phenomenon of bilingual authors who produce versions of their books in both their languages?

Can the second-language version, strictly speaking, be considered a translation of the first-language version or is it merely a somewhat looser interpretation? How do such authors approach the...

10 December 2020 5,092 25 View

How to distinguish CA1 pyramidal cell vs. interneuron using voltage-clamp?

I am doing voltage-clamp experiments in CA1 pyramidal cells (mEPSCs; AMPA-NMDA ratio; LTP; etc) from acute hippocampal slices in mice. I want to make sure I am only recording from excitatory...

29 October 2020 1,098 2 View

Why is SolidWorks giving high thermal stress in an unconstrained part?

I'm running a thermal simulation with a temperature change from 293K to 88K. It's all 6061 aluminum. The temperature load is applied to all exposed faces. This sim is of a single piece with a...

11 October 2020 3,125 3 View

Does FuDR dissolve/dilute into NGM plates when administered to plates?

I am currently trying to use FuDR to run a lifespan experiment using C. elegans. I have a stock solution of FuDR that has been dissolved in water and am trying the determine the concentration of...

27 August 2020 1,674 1 View

Increase Oleophilicity while decreasing hydrophilicity on silicon surfaces?

Hello RG community, currently I am trying to reach these goals on silicon surfaces for a microfludic project. I have used silanes like APTES in the past in order to get my si-surface hydrophobic...

22 March 2020 2,925 3 View

How could one improve the magnitude of t-statistics of a construct?

Hello All, I am not even sure if this is possible, but I have used this dataset for several publication -albeit with different constructs-and have not seen such low t-values. For example, I have a...

10 March 2020 1,164 3 View

How do I calculate the Mean and Standard Deviation for a set of items (i.e., that form a construct) in SPSS?

Hello All, I have been asked to supply the Mean and Standard Deviation for my latent constructs. Is there a straightforward way of doing it in SPSS? I am actually modeling in SmartPLS, but not...

04 March 2020 1,597 4 View

Any strategies for quantification and purification of a red pigment with no peaks in the visible region which is only soluble in water?

We have isolated a red pigment producing bacteria. We harvested the crude pigment by removing the cells by centrifugation. We tried to find the absorption maxima (lambda max) of the pigment using...

19 January 2020 1,331 2 View

How to Create Small Graphs for Interaction Effects?

Hello All, I have been able to calculate all the interaction effects for a study involving the Big Five. One of the interaction effects I would like to graph (among others) is the relationship...

30 December 2019 6,640 3 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close