Why in China case carburised grade like 20Mn Cr5 contains Titanium?

Veeraraghavan Pandurangan @Veeraraghavan_Pandurangan

12 December 2016 0 5K Report

Many Chinese grade steel contains Ti (0.04 to 0.1%) . why it is added?

Badges
Science topic

More Veeraraghavan Pandurangan's questions See All

Which automobile componets can be developed in squeeze casting in India?

which automobile components can be economically made by squeeze casting

03 April 2016 7,197 0 View

What is cost difference between SAE 15B41 and SAE 5140?

mention in % difference

31 December 2015 3,142 3 View

What is the general buy back period for a sand reclamation plant?

Sand processing capacity 2T/hour

31 December 2015 3,094 3 View

Is it possible to use Almen strip for assesing the quality of shot blasting of casting?

One can attempt to deploy the good practise of shot peening to shot blasting

11 December 2015 8,560 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

Dear colleagues, Can anybody by chance have pdfs of two books in Chinese: Liu (2003) and Zhang et al. (2004)?

Liu Zhaosheng. 2003. Triassic and Jurassic sporopollen assemblage from the Kuqa Depression，Tarim Basin of Xinjiang，NW China. Palaeontologia Sinica， New Series A，no. 14（Whole no. 190）....

28 July 2024 6,390 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Could international experts in media and journalism, AI, communications and international communication share this conference link?

"Integration of Mass Media and Communication into the System of International Relations: Place, Role, Actuality and Prospects: Modern Media Issues 2024" Website: https://immcir.alnoor.edu.iq/

23 July 2024 3,139 6 View